22017 datasheet(112/120 Pages) ITT

112 / 120 page

DPD/DPDMA

Stripping Instructions

112

www.ittcannon.com

Dimensions shown in inch (mm)

Specifications and dimensions subject to change

How to Order

ITT Cannon recommends resistance soldering for all

solder contacts, particularly for RF cable where

excessive heat will damage the dielectric. Wires

should be pre-tinned. Shells, bushings, endbells and

junction shells Jwhere applicable) must be slipped

over wire bundles before soldering or crimping is

started. The mechanical steps in wiring coaxials are

described below.

1. Cut cable even. Trim to dimensions shown on

tabulation. Care should be taken not to injure

the conductor or dielectric.

3. Remove solder pot cover. Insert cable and solder

conductor to contact. If a straight contact is

used, the dielectric should but against contact

solder pot.

4. Replace solder pot cover and solder braid to

ferrule.

2. Comb braid, tin conductor and remove flux. If a

90 contact is used, bend conductor 90˚ after

tinning.

Single Gang - DPD/DPDMA

The DPD/DPDMA can be engaged by means of a

No. 10-32 steel jack screw and clinch nut. This

coupling device is designed to fasten connectors

securely when they are used in other than standard

rack/ panel applications. The jack screws and clinch

nuts are mounted on the shell flanges at the factory.

They may be called out on either -33 or -34 shelis,

although it is preferred to have jack screws on the

-33 shell and the clinch nuts on the -34 shell. The

device can be ordered on both DPD and DPDMA.

Two Gang - DPD2/DPD2MA

The DPD2 is engaged by means of a variety of

screw mechanisms. Engaging devices are inter-

changeable (within the thread group) with male or

female mounting on either 33 or 34 shells. The

accompanying tabulation lists the available engag-

ing devices, male opposite female, with which they

mate.

R Coaxial (Straight and 90 )

Coax Type

Straight

R Coax

RG-7/U

RG-59/U

RG-62/U

RG-7/U

RG-58/U

RG-59/U

RG-62/U

.171 (4.34)

.218 (5.54)

.421 (10.69)

.546 (13.87)

.543 (13.87)

.312 (7.92)

.531 (13.49)

.515 (13.08)

.671 (17.04)

.437 (11.10)

.593 (15.06)

90 angle

R Coax

DPD-**-34*-1* N

DPD-**-33*-1* S

N = Clinch Nut

S = Jack Screw

The suffix "N" or "S" is placed immediately after the mounting

hole variation; i.e., - 1AN, -1AS, etc.

Engaging Device

DPD2

MALE ENGAGING DEVICES

Used On

Part

Number

DPD2

DPD2MA

CMRA

DM-1

DM-2

DM-3

DM-7

FEMALE ENGAGING DEVICES

#10-32 steel jack screw (on horizontal center line)

-34

Shell

#10-32

clinch nut

on horizontal

center line

1/4 hex with

screwdriver

slot &

safety wire

hole

-33

Shell

-72C2

-34PCM

Cable Size

BRAID

DIELECTRIC

CONDUCTOR

Straight

COVER

Trim

Engaging Devices

22017 Scheda tecnica(PDF) 112 Page - ITT Industries

22017 Scheda tecnica(HTML) 112 Page - ITT Industries

Html Pages

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65 66 67 68 69 70 71 72 73 74 75 76 77 78 79 80 81 82 83 84 85 86 87 88 89 90 91 92 93 94 95 96 97 98 99 100 ...More

Scheda tecnica Scarica

Link URL