1--21000--7 datasheet(3/6 Pages) TEC

Il numero della parte	1--21000--7

Spiegazioni elettronici	2 mm Common Termination Head Assembly

Download	6 Pages

Scroll/Zoom	100%

Produttore elettronici	TEC [TE Connectivity Ltd]

Homepage	http://www.te.com/usa-en/home.html

Logo

3 / 6 page

408- 9426

3

of 6

Rev E

Figure 4

Unstripped Wire Inserted

and Bottomed in Wire Guide

5. Release the feed pawl by pushing it forward

then move the carriage to left and remove the

connector from head assembly.

6. Inspect termination in accordance with

Application Specification 114--5103. If wire

insertion depth is incorrect or if the carriage is not

feeding properly, refer to Section 5.

5. ADJUSTMENTS

5.1. Wire Insertion Depth (See Figure 5)

A. For Pistol Grip Manual Handle Assembly

If the wire is too deep in the contact insulation

displacement slot, remove the head from the tool and

turn the adjuster 1/6--revolution clockwise. This will

reduce the wire insertion depth by approximately

0.20 mm [.008 in.]. Install the head onto the tool; then

terminate and inspect a sample connector.

If the wire is not deep enough in the contact insulation

displacement slot, remove the head from the tool and

turn the adjuster 1/6--revolution counterclockwise.This

will increase the wire insertion depth by approximately

0.20 mm [.008 in.]. Install the head onto the tool; then

terminate and inspect a sample connector.

B. For Pneumatic Assembly

To avoid personal injury, ALWAYS disconnect air

supply from pneumatic power bench when

removing head from tool.

1. Increase the air pressure for the pneumatic

bench mount in increments of 69 kPa [10 psi] until

proper wire insertion depth is obtained.

DO NOT increase the air pressure beyond

483 kPa [70 psi]; otherwise, excessive wear and

strain to the tool and head could result.

Figure 5

Turn Clockwise

to Reduce

Wire Insertion Depth

Turn Counterclockwise

to Increase

Wire Insertion Depth

2. If the proper wire insertion depth is not obtained,

set the air pressure to 276 kPa [40 psi], and follow

the procedure in Paragraph 5.1, A.

5.2. Carriage Feed

The carriage feed adjustment setscrew, shown in

Figure 6, controls the location of the carriage. If the

screw is positioned in too far, the feed pawl will not

engage in the carriage and the carriage will not

advance. If the screw is out too far, the carriage will

back up until the feed pawl engages, and thus, will

incorrectly position the contact to be terminated.

Adjust the carriage by turning the adjustment screw

either in or out until the contact aligns with the wire

inserter.

Figure 6

Carriage Feed

Adjustment Setscrew

Feed

Pawl

Carriage

DANGER

CAUTION

!

Codice articolo simile - 1--21000--7

Produttore elettronici	Il numero della parte	Scheda tecnica	Spiegazioni elettronici
TE Connectivity Ltd	1--21000--7	115Kb / 4P	Base Assembly Universal

More results

Descrizione simile - 1--21000--7

Produttore elettronici	Il numero della parte	Scheda tecnica	Spiegazioni elettronici
Tyco Electronics	408-4070	273Kb / 5P	Pneumatic Head Assembly
Samtec, Inc	2SN-BK-G	46Kb / 1P	2 mm C.L. SHUNT ASSEMBLY
Tyco Electronics	408-4260	155Kb / 7P	Mass Termination Assembly
TE Connectivity Ltd	408-7994	204Kb / 4P	Mass Termination Assembly
TE Connectivity Ltd	408-7995	244Kb / 6P	Mass Termination Assembly
Tyco Electronics	408-9607	142Kb / 5P	Feed- Through Head Assembly
3M Electronics	7893S	53Kb / 1P	3M??Head Strap/Harness Assembly 7893S, Silicone, 2 EA/Case
Tyco Electronics	59461	75Kb / 1P	HEAVY HEAD HAND TOOL ASSEMBLY
TE Connectivity Ltd	408-9736	225Kb / 4P	STRATO-THERM Die Head Assembly
NTE Electronics	NTE15043	18Kb / 2P	Integrated Circuit Head Amplifier Circuit for 2 Head VCR

More results

1--21000--7 Scheda tecnica(PDF) 3 Page - TE Connectivity Ltd

1--21000--7 Scheda tecnica(HTML) 3 Page - TE Connectivity Ltd

Codice articolo simile - 1--21000--7

Descrizione simile - 1--21000--7

Html Pages

1 2 3 4 5 6

Scheda tecnica Scarica

Link URL