OMAP3530ECUS datasheet(210/265 Pages) TI1

210 / 265 page

mcbspx_clkx

mcbspx_fsx

mcbspx_dx

030-075

OMAP3530, OMAP3525

SPRS507H – FEBRUARY 2008 – REVISED OCTOBER 2013

www.ti.com

Figure 6-40. McBSP Falling Edge Transmit Timing in Slave Mode

6.6.1.2

McBSP in TDM—Multipoint Mode (McBSP3)

For TDM application in multipoint mode, OMAP3530/25 is considered as a slave. Table 6-69 and Table 6-

70 assume testing over the operating conditions and electrical characteristic conditions described below.

Table 6-68. McBSP3 Timing Conditions—TDM in Multipoint Mode

TIMING CONDITION PARAMETER

VALUE

UNIT

MIN

MAX

Input Conditions

Input signal rising time

1.0

8.5

Input signal falling time

1.0

8.5

Output Conditions

CLOAD

Output Load Capacitance

Table 6-69. McBSP3 Timing Requirements—TDM in Multipoint Mode(1)

NO.

PARAMETER

1.15 V

1.0 V

UNIT

MIN

MAX

MIN

MAX

tW(CLKH)

Cycle Time, mcbsp3_clkx

162.8

tW(CLKH)

Typical Pulse duration, mcbsp3_clkx high

0.5*P(2)

tW(CLKL)

Typical Pulse duration, mcbsp3_clkx low

0.5*P(2)

tdc(CLK)

Duty cycle error, mcbsp3_clkx

–8.14

8.14

–8.14

8.14

B3(3)

tsu(DRV-CLKAE)

Setup time, mcbsp3_dr valid before

mcbsp3_clkx active edge

B4(3)

th(CLKAE-DRV)

Hold time, mcbsp3_dr valid after mcbsp3_clkx

2.4

active edge

B5(3)

tsu(FSV-CLKAE)

Setup time, mcbsp3_fsx valid before

mcbsp3_clkx active edge

B6(3)

th(CLKAE-FSV)

Hold time, mcbsp3_fsx valid after

2.4

mcbsp3_clkx active edge

(1)

For McBSP3, these timings concern only Set #3 (multiplexing mode in McBSP1 pins).

(2)

P = mcbsp3_clkx period in ns

(3)

See Section 6.6.1.1, McBSP in Normal Mode for corresponding figures.

Table 6-70. McBSP3 Switching Characteristics—TDM in Multipoint Mode(1)

NO.

PARAMETER

1.15 V

1.0 V

UNIT

MIN

MAX

MIN

MAX

B8(2)

td(CLKXAE-DXV)

Delay time, mcbsp3_clkx active edge to

0.6

16.8

0.6

29.6

mcbsp3_dx valid

(1)

For McBSP3, these timings concern only Set #3 (multiplexing mode in McBSP1 pins).

(2)

See Section 6.6.1.1, McBSP in Normal Mode for corresponding figures.

210

TIMING REQUIREMENTS AND SWITCHING CHARACTERISTICS

Submit Documentation Feedback

Product Folder Links: OMAP3530 OMAP3525

OMAP3530ECUS Scheda tecnica(PDF) 210 Page - Texas Instruments

OMAP3530ECUS Scheda tecnica(HTML) 210 Page - Texas Instruments

Html Pages

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65 66 67 68 69 70 71 72 73 74 75 76 77 78 79 80 81 82 83 84 85 86 87 88 89 90 91 92 93 94 95 96 97 98 99 100 ...More

Scheda tecnica Scarica

Link URL