GENERAL DESCRIPTION
MX25L12845E is 134,217,728 bits serial Flash memory, which is confgured as 16,777,216 x 8 internally. When it is in two or four I/O mode, the structure becomes 67,108,864 bits x 2 or 33,554,432 bits x 4. The MX25L12845E features a serial peripheral interface and software protocol allowing operation on a simple 3-wire bus. The three bus signals are a clock input (SCLK), a serial data input (SI), and a serial data output (SO). Serial access to the device is enabled by CS# input.
MX25L12845E provides high performance read mode, which may latch address and data on both rising and falling edge of clock. By using this high performance read mode, the data throughput may be doubling. Moreover, the performance may reach direct code execution, the RAM size of the system may be reduced and further saving system cost.
MX25L12845E, MXSMIO (Serial Multi I/O) flash memory, provides sequential read operation on the whole chip and multi-I/O features.

FEATURES
GENERAL
• Serial Peripheral Interface compatible -- Mode 0 and Mode 3
• 128Mb: 134,217,728 x 1 bit structure or 67,108,864 x 2 bits (two I/O mode) structure or 33,554,432 x 4 bits (four I/O mode) structure
• 4096 Equal Sectors with 4K bytes each
   - Any Sector can be erased individually
• 512 Equal Blocks with 32K bytes each
   - Any Block can be erased individually
• 256 Equal Blocks with 64K bytes each
   - Any Block can be erased individually
• Power Supply Operation
   - 2.7 to 3.6 volt for read, erase, and program operations
• Latch-up protected to 100mA from -1V to Vcc +1V

PERFORMANCE
• High Performance
   VCC = 2.7~3.6V
   - Normal read
      - 50MHz
   - Fast read (Normal Serial Mode)
      - 1 I/O: 104MHz with 8 dummy cycles
      - 2 I/O: 70MHz with 4 dummy cycles
      - 4 I/O: 70MHz with 6 dummy cycles
   - Fast read (Double Transfer Rate Mode)
      - 1 I/O: 50MHz with 6 dummy cycles
      - 2 I/O: 50MHz with 6 dummy cycles
      - 4 I/O: 50MHz with 8 dummy cycles
   - Fast program time: 1.4ms(typ.) and 5ms(max.)/page (256-byte per page)
   - Byte program time: 9us (typical)
   - Continuously Program mode (automatically increase address under word program mode)
   - Fast erase time: 60ms (typ.)/sector (4K-byte per sector) ; 0.7s(typ.) /block (64K-byte per block); 80s(typ.) /chip
• Low Power Consumption
   - Low active read current: 19mA(max.) at 104MHz, 15mA(max.) at 66MHz and 10mA(max.) at 33MHz
   - Low active programming current: 25mA (max.)
   - Low active erase current: 25mA (max.)
   - Low standby current: 100uA (max.)
   - Deep power down current: 40uA (max.)
• Typical 100,000 erase/program cycles

SOFTWARE FEATURES
• Input Data Format
   - 1-byte Command code
• Advanced Security Features
   - BP0-BP3 block group protect
   - Flexible individual block protect when OTP WPSEL=1
   - Additional 4K bits secured OTP for unique identifer
• Auto Erase and Auto Program Algorithms
   - Automatically erases and verifes data at selected sector
   - Automatically programs and verifes data at selected page by an internal algorithm that automatically times the program pulse width (Any page to be programed should have page in the erased state frst.)
• Status Register Feature
• Electronic Identifcation
   - JEDEC 1-byte Manufacturer ID and 2-byte Device ID
   - RES command for 1-byte Device ID
   - REMS, REMS2, REMS4 and REMS4D commands for 1-byte Manufacturer ID and 1-byte Device ID
• Support Serial Flash Discoverable Parameters (SFDP) mode

HARDWARE FEATURES
• SCLK Input
   - Serial clock input
• SI/SIO0
   - Serial Data Input or Serial Data Input/Output for 2 x I/O mode and 4 x I/O mode
• SO/SIO1/PO7
   - Serial Data Output or Serial Data Input/Output for 2 x I/O mode and 4 x I/O mode or Parallel Data
• WP#/SIO2
   - Hardware write protection or serial data Input/Output for 4 x I/O mode
• NC/SIO3
   - NC pin or serial data Input/Output for 4 x I/O mode
• PO0~PO6
   - For parallel mode data (only 128Mb provide parallel mode)
• PACKAGE
   - 16-pin SOP (300mil)
   - 8-WSON (8x6mm)
   - All devices are RoHS Compliant and Halogen-free