ADC12L080 datasheet(7/23 Pages) NSC

7 / 23 page

DC and Logic Electrical Characteristics (Continued)

Unless otherwise specified, the following specifications apply for AGND = DGND = DR GND = 0V, V

A =VD = +3.3V, VDR =

+2.5V, PD = 0V, V

REF = +1.0V external, VCM = 1.65V, RS < 100

Ω,f

CLK = 80 MHz, tr =tf = 2 ns, fIN = 70 MHz, CL = 15 pF/pin.

Boldface limits apply for T

J =TMIN to TMAX: all other limits TJ = 25˚C (Notes 7, 8, 9, 10)

Symbol

Parameter

Conditions

Typical

(Note 10)

Limits

(Note 10)

Units

(Limits)

POWER SUPPLY CHARACTERISTICS

Analog Supply Current

PD Pin = DGND

PD Pin = V

120

168

mA (max)

Digital Supply Current

PD Pin = DGND

PD Pin = V

11.5

mA (max)

Digital Output Supply Current

PD Pin = DGND, f

in = 0, (Note 13)

PD Pin = V

Total Power Consumption

PD Pin = DGND, C

L = 0 pF (Note 14)

PD Pin = V

425

590

mW (max)

PSRR1 Power Supply Rejection Ratio

Rejection of Full-Scale Gain Error

change with V

A = 3.0V vs. 3.6V

AC Electrical Characteristics

Unless otherwise specified, the following specifications apply for AGND = DGND = DR GND = 0V, V

A =VD = +3.3V, VDR =

+2.5V, PD = 0V, V

REF = +1.0V external, VCM = 1.65V, RS < 100

Ω,f

CLK = 80 MHz, tr =tf = 2 ns, fIN = 70 MHz, CL = 15 pF/pin.

Boldface limits apply for T

J =TMIN to TMAX: all other limits TJ = 25˚C (Notes 7, 8, 9, 10, 11)

Symbol

Parameter

Conditions

Typical

(Note 10)

Limits

(Note 10)

Units

(Limits)

Maximum Clock Frequency

MHz (min)

Minimum Clock Frequency

MHz

Clock Duty Cycle

% (max)

% (min)

Clock High Time

5.5

ns (min)

Clock Low Time

5.5

ns (min)

CONV

Conversion Latency

Clock

Cycles

Data Output Delay after Rising

CLK Edge

DR = 2.5V

5.2

8.3

ns (max)

DR = 3.3V

4.8

7.5

ns (max)

Aperture Delay

Aperture Jitter

0.7

ps rms

Power Down Mode Exit Cycle

0.1 µF on pins 30, 31, 32,

and 1.0 µF from pin 30 to 31

1µs

Note 1: Absolute Maximum Ratings indicate limits beyond which damage to the device may occur. Operating Ratings indicate conditions for which the device is

functional, but do not guarantee specific performance limits. For guaranteed specifications and test conditions, see the Electrical Characteristics. The guaranteed

specifications apply only for the test conditions listed. Some performance characteristics may degrade when the device is not operated under the listed test

conditions.

Note 2: All voltages are measured with respect to GND = AGND = DGND = 0V, unless otherwise specified.

Note 3: When the input voltage at any pin exceeds the power supplies (that is, VIN < AGND, or VIN > VA,VD or VDR), the current at that pin should be limited to

25 mA. The 50 mA maximum package input current rating limits the number of pins that can safely exceed the power supplies with an input current of 25 mA to two.

Note 4: The absolute maximum junction temperature (TJmax) for this device is 150˚C. The maximum allowable power dissipation is dictated by TJmax, the

junction-to-ambient thermal resistance (

θJA), and the ambient temperature, (TA), and can be calculated using the formula PDMAX=(TJmax - TA )/θJA. The values

for maximum power dissipation will be reached only when the device is operated in a severe fault condition (e.g. when input or output pins are driven beyond the

power supply voltages, or the power supply polarity is reversed). Obviously, such conditions should always be avoided.

Note 5: Human body model is 100 pF capacitor discharged through a 1.5 k

Ω resistor. Machine model is 220 pF discharged through 0Ω.

Note 6: The 235˚C reflow temperature refers to infrared reflow. For Vapor Phase Reflow (VPR), the following Conditions apply: Maintain the temperature at the top

of the package body above 183˚C for a minimum 60 seconds. The temperature measured on the package body must not exceed 220˚C. Only one excursion above

183˚C is allowed per reflow cycle.

Note 7: The inputs are protected as shown below. Input voltages above VA or below GND will not damage this device, provided current is limited per (Note 3).

However, errors in the A/D conversion can occur if the input goes above VA or below GND by more than 100 mV. As an example, if VA is 3.3V, the full-scale input

voltage must be

≤3.4V to ensure accurate conversions.

ADC12L080 Scheda tecnica(PDF) 7 Page - National Semiconductor (TI)

ADC12L080 Scheda tecnica(HTML) 7 Page - National Semiconductor (TI)

Html Pages

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23

Scheda tecnica Scarica

Link URL