THIS CATALOG PAGE IS FOR REFERENCE ONLY. REQUEST A

CERTIFIED UMPCO DRAWING FOR ACTUAL SPECIFICATIONS.

ANY CONFLICT BETWEEN THIS DOCUMENT AND THE CERTIFIED

DRAWING, THE CERTIFIED DRAWING WILL TAKE PRECEDENCE.

IF THE DOCUMENT IS CONTROLLED BY ANY OTHER SOURCE

THAN UMPCO, THE CERTIFIED DRAWING MUST BE PURCHASED

THROUGH THAT ORGANIZATION.

CAGE CODE No. 18076

REV

A

07/26/11

NAS1715

CLAMP, LOOP CUSHIONED

PART NUMBER

7100 LAMPSON AVE * PO BOX 5158 * GARDEN GROVE, CA 92846-5158 SALES: (714) 897-3531 * BUS: (714) 897-3536 * FAX: (714) 897-2611

EXAMPLE OF PART NUMBER:

NAS1715 D 7 T W H

NOTES:

/1/

STANDARD SIZE LIMITATIONS:

.125 THRU 1.500 BY .0625 INCREMENTS

1.625 THRU 2.500 BY .125 INCREMENTS

2.750 AND ABOVE BY .250 INCREMENTS

2.

TEMPERATURE RANGE:

CUSHION:

CHLOROPRENE RUBBER

-40°F TO +212°F

SILICONE RUBBER

-80°F TO +450°F (SHORT DURATION EXCURSIONS TO 500°F)

PTFE

-320°F TO +500°F

FABRIC

+554°F

STRAP:

ALUMINUM

-320 °F TO +200 °F

CRES

-320 °F TO +600 °F

/3/

CUSHION THICKNESS:

ALL SIZES FABRIC .062

SIZES THRU –8, RUBBER .045

SIZES –9 THRU –66, RUBBER, .062

PTFE, CODE “K” & “T” (NON-WEDGE) .020 +.008/-.004

PTFE, CODE “KW” & “TW” (WEDGE TYPE) .030 +.011/-.005

/4/

CLAMP SHALL CHECK TO DIMENSIONS WITH ENDS HELD IN POSITION SHOWN BY DIMENSION G.

/5/

WEDGE MAY BE INTEGRALLY MOLDED TO CUSHION OR VULCANIZED TO CUSHION.

6.

METAL STRAP SHALL BE FREE OF BURRS AND SHARP EDGES.

7.

COMPLETE NAS PART NUMBER, AND MANUFACTURER’S IDENTIFICATION SHALL BE MARKED ON EACH CLAMP IN AN AREA NOT

COVERED BY CUSHION OR MOUNTING HARDWARE EXCEPT SIZES –2, -3, AND –4, WHICH SIZES SHALL BE IDENTIFIED BY

STRAP MATERIAL, DASH NUMBER, CUSHION MATERIAL AND MANUFACTURER’S IDENTIFICATION, E.G. D2T XX

8.

DIMENSIONS IN INCHES.

/9/

WEDGE NOT AVAILABLE ON PTFE CUSHION CLAMP, CODE “K” AND “T” ON SIZES 2 THRU 5.

10.

DELETED

11.

DELETED

/12/

STIFFENER BEAD CONSTRUCTION ON CLAMP SIZES 5 AND ABOVE

13.

DELETED

/14/

CUSHION TYPES “A” AND “M” ARE INACTIVE FOR DESIGN AFTER MARCH 31, 1994. SUPERSEDED BY TYPE “Z”. FOR

DESCRIPTION OF STATUS NOTES SEE NAS380.

/15/

WEDGE NOT AVAILABLE ON FABRIC CUSHIONED CLAMP, CODE “Z”.

16.

DIMENSIONING AND TOLERANCES PER ANSI Y14.5M-1982.

/17/

.265 DIAMETER OR .213 TO .223 DIAMETER OPTION AVAILABLE WHEN SPECIFIED BY PART NUMBER.

18.

TOLERANCES UNLESS OTHERWISE SPECIFIED: 2 PLACES ±.03, 3 PLACES ±.010.

= CLAMP, LOOP, CENTER, MOUNTED, .032 ALUMINUM

ALLOY, .438 DIA, PTFE CUSHION, SODIUM TREATED,

WEDGE TYPE, .265 DIA MOUNTING HOLE

MOUNTING HOLE DIA:

H= .265

X = .213 TO .223

OMIT CODE = .204

WEDGE CODE:

W = WEDGE

OMIT CODE = NO WEDGE

CUSHION:

K = PTFE, NATURAL

N = CHLOROPRENE RUBBER

S = SILICONE RUBBER

T = PTFE, SODIUM TREATED

Z = FABRIC, PBI/PTFE IMPREGNATED

DASH NUMBER, D DIAMETER IN .0625 INCREMENTS

MATERIAL:

D = ALUMINUM ALLOY AND THICKNESS PER TABLE 1

DT = ALUMINUM ALLOY AND THICKNESS PER TABLE 1

C = CRES AND THICKNESS PER TABLE 1

CT = CRES AND THICKNESS PER TABLE 1

DOCUMENT NUMBER