THIS CATALOG PAGE IS FOR REFERENCE ONLY. REQUEST A

CERTIFIED UMPCO DRAWING FOR ACTUAL SPECIFICATIONS.

ANY CONFLICT BETWEEN THIS DOCUMENT AND THE CERTIFIED

DRAWING, THE CERTIFIED DRAWING WILL TAKE PRECEDENCE.

IF THE DOCUMENT IS CONTROLLED BY ANY OTHER SOURCE

THAN UMPCO, THE CERTIFIED DRAWING MUST BE PURCHASED

THROUGH THAT ORGANIZATION.

CAGE CODE No. 18076

REV

N/C

02/05/09

AS9601

BRACKET, ANGLE 90°, CRES UNS S41000

.190 X .250 BOLT

PART NUMBER

7100 LAMPSON AVE * PO BOX 5158 * GARDEN GROVE, CA 92846-5158 SALES: (714) 897-3531 * BUS: (714) 897-3536 * FAX: (714) 897-2611

DIRECTION OF GRAIN

(SEE NOTE 4)

R .510/.490

Ø .210/.200

B

.205

.195

MARK PART

NUMBER AND

MANUFACTURER’S

IDENTIFICATION

PER AS478 CLASS D

.510

.490

A

R .135/.115

MS9601-XXX

.255

.245

.068

.058

95°

85°

.235

.225

R .510/.490

Ø .270/.260

NOTES:

1.

MATERIAL: CORROSION RESISTANT STEEL PER AMS 5504 (UNS S41000).

2.

HARDNESS: 30-38 HRC.

3.

FINISH: HEAT TREATMENT AND CLEANING IN ACCORDANCE WITH AMS 2550.

4.

GRAIN FLOW SHALL BE PARALLEL WITH ROLLING DIRECTION.

5.

REMOVE BURRS AND BREAK SHARP EDGES .003 -.015, UNLESS OTHERWISE SPECIFIED.

6.

DIMENSIONING AND TOLERANCES PER ANSI Y14.5M-1982

7.

DIMENSIONS ARE IN INCHES

8.

DO NOT USE UNASSIGNED PART NUMBERS

9.

APPROXIMATE MASS LB/100 = .877 (A+B) + .145

FIGURE 1 - ANGLE BRACKET

B

.490 - .510

.552 - .572

.615 - .635

.678 - .698

.740 - .760

LENGTH

PART NUMBER

PART NUMBER

PART NUMBER

PART NUMBER

PART NUMBER

0.428 - 0.448

MS9601-005

MS9601-035

MS9601-065

MS9601-095

MS9601-125

0.490 - 0.510

MS9601-006

MS9601-036

MS9601-066

MS9601-096

MS9601-126

0.552 - 0.572

MS9601-007

MS9601-037

MS9601-067

MS9601-097

MS9601-127

0.615 - 0.635

MS9601-008

MS9601-038

MS9601-068

MS9601-098

MS9601-128

0.678 - 0.698

MS9601-009

MS9601-039

MS9601-069

MS9601-099

MS9601-129

0.740 - 0.760

MS9601-010

MS9601-040

MS9601-070

MS9601-100

MS9601-130

0.802 - 0.822

MS9601-011

MS9601-041

MS9601-071

MS9601-101

MS9601-131

0.865 - 0.885

MS9601-012

MS9601-042

MS9601-072

MS9601-102

MS9601-132

0.928 - 0.948

MS9601-013

MS9601-043

MS9601-073

MS9601-103

MS9601-133

0.990 - 1.010

MS9601-014

MS9601-044

MS9601-074

MS9601-104

MS9601-134

1.052 - 1.072

MS9601-015

MS9601-045

MS9601-075

MS9601-105

MS9601-135

1.115 - 1.135

MS9601-016

MS9601-046

MS9601-076

MS9601-106

MS9601-136

1.178 - 1.198

MS9601-017

MS9601-047

MS9601-077

MS9601-107

MS9601-137

1.240 - 1.260

MS9601-018

MS9601-048

MS9601-078

MS9601-108

MS9601-138

1.302 - 1.322

MS9601-019

MS9601-049

MS9601-079

MS9601-109

MS9601-139

1.365 - 1.385

MS9601-020

MS9601-050

MS9601-080

MS9601-110

MS9601-140

1.428 - 1.448

MS9601-021

MS9601-051

MS9601-081

MS9601-111

MS9601-141

1.490 - 1.510

MS9601-022

MS9601-052

MS9601-082

MS9601-112

MS9601-142

TABLE 1 -PART NUMBERS AND DIMENSIONS

A - LENGTH