 |
Motore di ricerca datesheet componenti elettronici |
|
|
Motore di ricerca datesheet componenti elettronici |
|
RFSA2113 Scheda tecnica(PDF) 2 Page - Qorvo, Inc |
|
|
|||||||||||||||||||||||||||||
RFSA2113 Scheda tecnica(HTML) 2 Page - Qorvo, Inc |
|
|
2 / 19 page  RFSA2113 Wide Bandwidth Voltage Controlled Attenuator Data Sheet, September 2, 2016 | Subject to change without notice 2 of 19 www.qorvo.com ® Absolute Maximum Ratings Parameter Range / Value Units Exceeding these absolute maximum ratings during operation of this device may cause permanent damage. Device Voltage (VDD) −0.5 to +6 V SLOPE, VC, EN Pins −0.5 to +6 V RF Input Power (1) +23 dBm Storage Temperature −55 to +150 °C Junction Temperature ( Tj) +125 °C Notes: 1. Peak power of +29 dBm allowable when RMS power does not exceed +23 dBm. Recommended Operating Conditions Parameter Min Typ Max Units Electrical specifications are measured under bias, signal and temperature conditions as specified. Specifications are not guaranteed over all recommended operating conditions. Device Voltage (VDD) +3.0 +5.0 +5.5 V TCASE −40 +85 °C Electrical Specifications Parameter Conditions (1) Min Typ Max Units Operational Frequency Range 50 18000 MHz Minimum Insertion Loss 1 GHz 2 2.8 dB 10 GHz 3 4.5 18 GHz 4.5 Gain Control Range 1 GHz 32 34 dB 10 GHz 30 32 18 GHz 28 Gain vs. Temperature Peak to peak gain variation over temperature for fixed control voltage 1 dB Return Loss 15 dB Relative Phase Insertion phase at 15 dB attenuation relative to minimum insertion loss 14 °Degrees Input1dB Compression Point Peak power of +29 dBm allowable when RMS power does not exceed +23 dBm. *Not Production Tested +22 +29 dBm Input IP3 PIN + (IM3dBC / 2) +38 +45 dBm Input IP2 PIN + IM2dBC, IM2 is F1+F2 +75 dBm Input IH2 PIN + H2dBC, H2 is second harmonic +80 dBm Input IH3 PIN + (H3dBC / 2), H3 is third harmonic +50 dBm Device Current, IDD 2 3.5 mA Thermal Resistance, θjc Junction to case 175 °C/W Voltage Control Range, Positive Attenuation Slope +2.5 V control voltage is lowest insertion loss, SLOPE pin logic high 0 +2.5 V Voltage Control Range, Negative Attenuation Slope 0 V control voltage is lowest insertion loss, SLOPE pin logic low 0 +2.5 V Voltage Control Pin Current VC pin set to +2.5 V 1.2 µA SLOPE and EN Pins Logic Low +0.4 V SLOPE and EN Pins Logic High +1 V Settling Time 1 dB atten. change settling within 0.1 dB of final value. 2 µsec Notes: 1. Test conditions unless otherwise noted: VDD=+5 V, Temp.=+25 °C, 50 Ω system, Freq.=10 GHz. |
|
|
Link URL |
| Lei ha avuto il aiuto da alldatasheet? [ DONATE ] |
Di alldatasheet | Richest di pubblicita | contatti | Privacy Policy | Collegamento alla scheda tecnica | scambio Link | Ricerca produttore All Rights Reserved©Alldatasheet.com |
| Russian : Alldatasheetru.com | Korean : Alldatasheet.co.kr | Spanish : Alldatasheet.es | French : Alldatasheet.fr | Italian : Alldatasheetit.com Portuguese : Alldatasheetpt.com | Polish : Alldatasheet.pl | Vietnamese : Alldatasheet.vn Indian : Alldatasheet.in | Mexican : Alldatasheet.com.mx | British : Alldatasheet.co.uk | New Zealand : Alldatasheet.co.nz |
|
Family Site : ic2ic.com |
icmetro.com |
Italian ▼
English
Chinese
German
Japanese
Russian
Korean
Spanish
French
Italian
Portuguese
Polish
Vietnamese
Indian
Mexican
British
New Zealand
