WLG2-LDAS datasheet(47/52 Pages) OMRON

47 / 52 page

WL-N/WLM-N

Using the Switches

Item

Applicable models and Actuators

Details

Changing the Installation Position

of the Actuator

By loosening the Allen-head bolt on

the actuator lever, the position of the

actuator can be set anywhere within

the 360

°.

With Indicator-equipped Switches, the

actuator lever comes in contact with

the top of the indicator cover, so use

caution when rotating and setting the

lever.

When the lever only moves forwards

and backwards, it will not contact the

lamp cover.

(This does not apply to Long-life

Switches.)

Roller Levers:

(WLCA2-N, WLCA2-2-N,

WLCA2-2N-N, WLG2-N,

WLCA2-7-N, WLCA2-8-N,

WLGCA2-N, WLMCA2-N,

WLMG2-N, WLMGCA2-N)

Adjustable Roller Levers:

(WLCA12-N, WLCA12-2-N,

WLCA12-2N-N, WLG12-N)

Adjustable rod lever:

(WLCL-N, WLCL-2-N,

WLCL-2N-N, WLGL-N,

WLCAL4-N, WLCAL5-N)

Changing the Orientation of the

Head

By removing the two screws of the

Head, the Head can be set in any of

the four directions.

Be sure to change the plunger for

internal operations at the same time.

The roller plunger can be set in either

of two positions at 90°

Roller Levers:

(WLCA2-N, WLCA2-2-N,

WLCA2-2N-N, WLG2-N,

WLCA2-7-N, WLCA2-8-N,

WLGCA2-N, WLMCA2-N,

WLMG2-N, WLMGCA2-N)

Adjustable Roller Levers:

(WLCA12-N, WLCA12-2-N,

WLCA12-2N-N, WLG12-N)

Adjustable rod lever:

(WLCL-N, WLCL-2-N,

WLCL-2N-N, WLGL-N,

WLCAL4-N, WLCAL5-N)

Horizontal plunger

(WLSD

@-N)

Sealed top-roller plunger

(WLD28-N)

Note: Does not include the -RP60

Series or -141 Series.

Changing the Operating Direction

By removing the Head on models

which can operate on one-side only,

and then changing the direction of the

operational plunger, one of three

operating directions can be selected.

Roller Levers:

(WLCA2-N, WLCA2-2-N,

WLCA2-2N-N, WLG2-N,

WLCA2-7-N, WLCA2-8-N,

WLGCA2-N, WLMCA2-N,

WLMG2-N, WLMGCA2-N)

Adjustable Roller Levers:

(WLCA12-N, WLCA12-2-N,

WLCA12-2N-N, WLG12-N)

Adjustable rod lever:

(WLCL-N, WLCL-2-N,

WLCL-2N-N, WLGL-N,

WLCAL4-N, WLCAL5-N)

Installing the Roller on the Inside

By installing the roller lever in the

opposite direction, the roller can be

installed on the inside.

(Set so that operation can be

completed within a 180

° level range.)

Roller Levers:

(WLCA2-N, WLCA2-2-N,

WLCA2-2N-N, WLG2-N,

WLCA2-7-N, WLCA2-8-N,

WLGCA2-N, WLMCA2-N,

WLMG2-N, WLMGCA2-N)

Fork lever lock:

(WLCA32-4

@-N)

Note: Except for Switches with

variable roller levers.

Loosen the Allen-head bolt, set

the actuator's position and then

tighten the bolt again.

Head

Loosen the screws.

Operating

Not operating

Operating

Not operating

Operation in both

directions

Clockwise operation

Counterclockwise

operation

The output of the Switch will be

changed, regardless of which

direction the lever is pushed.

The output of the Switch will

only be changed when the lever

is pushed in one direction.

Loosen the

Allen-head bolt.

WLG2-LDAS Scheda tecnica(PDF) 47 Page - Omron Electronics LLC

WLG2-LDAS Scheda tecnica(HTML) 47 Page - Omron Electronics LLC

Html Pages

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52

Scheda tecnica Scarica

Link URL