V40006903 datasheet(9/63 Pages) TOSHIBA

9 / 63 page

Pinning:

1. Output (1)

2. +Vs

3. Output (2)

4. Mute / St-By

5. -Vs

6. Input (2)

7. Ground

8. Input (1)

VIDEO INPUT AND OUTPUT SOURCE SWITCHING

TEA6415C

Video switching is performed by the I2C controlled IC TEA6415C with a gain of 0dB. Inputs to the video switch are IF_CVBS,

three SCART video signals, front-AV video signal, SVHS luma signal, and one of SC1_R or SVHS_C. Outputs of the video

switch are three SCART video signals (SC1_OUT_V and SC3_OUT_V are the same), one video output for the PIP module,

Chroma signal (C), and luma (Y) or CVBS signal.

Features:

n 20 MHz Bandwith

n Cascadable with another TEA6415C (Internal address can be changed by pin 7 voltage)

n 8 inputs (CVBS, RGB, Mac, CHROMA, )

n 6 Outputs

n Possibility of MAC or chroma signal for each input by switching-off the clamp with an external resistor bridge

n Bus controlled

n 6.5dB gain between any input and output

n -55dB crosstaljk at 5MHz

n Fully ESD protected

Pinning:

1. Input

: Max

: 2Vpp, Input Current : 1mA, Max : 3mA

2. Data

: Low level : -0.3V

Max

: 1.5V,

High level : 3.0V

Max

: Vcc+0.5V

3. Input

: Max

: 2Vpp, Input Current : 1mA, Max : 3mA

4. Clock

: Low level : -0.3V

Max

: 1.5V,

High level : 3.0V

Max

: Vcc+0.5V

5. Input

: Max

: 2Vpp, Input Current : 1mA, Max : 3mA

6. Input

: Max

: 2Vpp, Input Current : 1mA, Max : 3mA

7. Prog

8. Input

: Max

: 2Vpp, Input Current : 1mA, Max : 3mA

9. Vcc

: 12V

10. Input

: Max

: 2Vpp, Input Current : 1mA, Max : 3mA

11. Input

: Max

: 2Vpp, Input Current : 1mA, Max : 3mA

12. Ground

13. Output

: 5.5Vpp, Min : 4.5Vpp

14. Output

: 5.5Vpp, Min : 4.5Vpp

15. Output

: 5.5Vpp, Min : 4.5Vpp

16. Output

: 5.5Vpp, Min : 4.5Vpp

17. Output

: 5.5Vpp, Min : 4.5Vpp

18. Output

: 5.5Vpp, Min : 4.5Vpp

19. Ground

20. Input

: Max

: 2Vpp, Input Current : 1mA, Max : 3mA

VIDEO OUTPUT AMPLIFIER STAGE

TDA6111Q

The TDA6111Q is a video output amplifier with 16Mhz bandwidth. It has a high slew rate.Automatic black-current stabilisation

is possible by black-current measurement output. It has two cathode outputs: one for DC currents and one for transient

currents. A feedback output is separated from the cathode outputs. An internal protection exists against positive appearing

cathode-ray-tube flashover discharges with ESD protection.

Features:

n High bandwidth and slew rate

n Black-current measurement output for Automatic Black-current Stabilisation (ABS)

n Two cathode outputs; one for DC currents, and one for transient currents

n A feedback output separated from the cathode outputs

n Internal protection against positive appearing cathode-ray Tube (CRT) flashover discharges

n ESD protection

n Simple application with a variety of colour decoders

n Differential input with a designed maximum common mode input capacitance of 3pF, a maximum differential

mode input capacitance of 0.5 pF and a differential input voltage temperature drift of 50 uV/K

n Defined switch-off behaviour.

V40006903 Scheda tecnica(PDF) 9 Page - Toshiba Semiconductor

V40006903 Scheda tecnica(HTML) 9 Page - Toshiba Semiconductor

Html Pages

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63

Scheda tecnica Scarica

Link URL