PIN OUT

MODEL NUMBERING KEY

RECOMMENDED OPERATING CONDITIONS

TYPICAL CHARACTERISTICS

INHIBIT

ABSOLUTE MAXIMUM RATINGS

MHL0512D

MHL0515D

PARAMETER

CONDITIONS

MIN

TYP

MAX

MIN

TYP

MAX

UNITS

OUTPUT VOLTAGE

11.88

12.00

12.12

14.85

15.00

15.15

VDC

11.88

12.00

12.12

±14.85

15.00

15.15

—

—

1.25

—

—

1.00

A

Tc = –55°C TO +85°C

—

—

15.0

—

—

15.0

W

OUTPUT RIPPLE

BW = 1 MHz

—

40

100

—

40

120

mV p-p

LINE REGULATION

—

0.05

0.10

—

0.05

0.10

%

—

0.05

0.15

—

0.05

0.15

LOAD REGULATION

—

0.05

0.15

—

0.03

0.10

%

NO LOAD TO FULL

—

0.25

0.50

—

0.20

0.40

—

2.2

3.5

—

1.9

3.0

%

—

2.2

3.5

—

1.9

3.0

INPUT VOLTAGE

Tc = –55°C TO +85°C

4

5

8

4

5

8

VDC

INPUT CURRENT

NO LOAD

—

120

150

—

140

180

FULL LOAD

—

—

4500

—

—

4500

mA

INHIBITED

—

20

—

—

20

—

INPUT RIPPLE CURRENT

—

50

120

—

70

150

mA p-p

EFFICIENCY

FULL LOAD

—

78

—

—

78

—

%

Input Voltage

• 4 to 8 VDC

Output Power

• 15 watts

Lead Soldering Temperature (10 sec per lead)

• 300°C

Storage Temperature Range (Case)

• –55°C to +125°C

B4-18

MHL SERIES

15 WATT

Output Voltage Temperature Coefficient

• 150 ppm/°C, typical

Input to Output Capacitance

• 80 pF typical

Isolation

• 100 megohm minimum at 500 V

Conversion Frequency

• 210 kHz, typical

Input Voltage Range

• 4 to 8 VDC continuous

Case Operating Temperature (Tc)

• –55°C to +85°C full power

• –55°C to +115°C absolute

Derating Output Power/Current

• Linearly from 100% at 85°C to 0% at 115° C

Notes

1. 95% of the maximum current or power is available from either output. The total of both outputs must not exceed the

maximum specification.

2. The effect on the positive output when it is held at 50 mA while the negative output is varied from 50 to 950 mA.

The effect on the negative output when it is held at 50 mA while the positive output is varied from 50 to 950 mA.

Inhibit TTL Open Collector

• Logic low (output disabled)

• Referenced to input common

• Logic high (output enabled)

Open collector

Pin

Designation

1,2

Positive Input

3

Positive Output

4

Output Common

5

Negative Output

6

No Connection

7

Case Ground

8

Inhibit

9, 10

Input Common

Electrical Characteristics: 25°C Tc, 5 VDC Vin, 100% load, unless otherwise specified.

BOTTOM VIEW

MHL

Squared corner and dot on

top of cover indicate pin one.

Dotted line outlines

flanged package

option.

10

9

8

7

6

123

4

5

See Section B8, cases F4 and J5 for dimensions.

MHL

05 12

S

F / ES

Base Model

Input Voltage

Output Voltage

Screening

Number of Outputs

Case Option

(Non-flanged case has no designator in

this position)

(S = single, D = dual)

(Standard screening has no designator

in this position.)

23002-001-DTS Rev A

DQ# 1018

All technical information is believed to be accurate, but no responsibility is

assumed for errors or omissions. Interpoint reserves the right to make changes in

products or specifications without notice. MHL Series is a trademark of Interpoint.

Copyright © 1994 - 1999 Interpoint. All rights reserved.