ADN2817 datasheet(23/35 Pages) AD

23 / 35 page

Preliminary Technical Data

ADN2817/ADN2818

Rev.Pr A | Page 23 of 35

and returns a ratio of the two frequencies to 0.01% (100 ppm).

The accuracy error of the reference clock is added to the

accuracy of the ADN2817/ADN2818 data rate measurement.

For example, if a 100-ppm accuracy reference clock is used, the

total accuracy of the measurement is within 200 ppm.

The reference clock can range from 12.3 MHz and 200 MHz.

The ADN2817/ADN2818 expects a reference clock between

12.3 MHz and 25 MHz by default. If it is between 25 MHz and

50 MHz, 50 MHz and 100 MHz, or 100 MHz and 200 MHz, the

user needs to configure the ADN2817/ADN2818 to use the

correct reference frequency range by setting two bits of the

CTRLA register, CTRLA[7:6]. Using the reference clock to

determine the frequency of the incoming data does not affect

the manner in which the part locks onto data. In this mode, the

reference clock is used only to determine the frequency of the

data. For this reason, the user does not need to know the data

rate to use the reference clock in this manner.

Prior to reading back the data rate using the reference clock, the

CTRLA[7:6] bits must be set to the appropriate frequency range

with respect to the reference clock being used. A fine data rate

readback is then executed as follows:

Step 1: Write a 1 to CTRLA[1]. This enables the fine data rate

measurement capability of the ADN2817/ADN2818. This bit is

level sensitive and does not need to be reset to perform

subsequent frequency measurements.

Step 2: Reset MISC[2] by writing a 1 followed by a 0 to

CTRLB[3]. This initiates a new data rate measurement.

Step 3: Read back MISC[2]. If it is 0, then the measurement is

not complete. If it is 1, then the measurement is complete and

the data rate can be read back on FREQ[22:0]. The time for a

data rate measurement is typically 80 ms.

Step 4: Read back the data rate from registers FREQ2[6:0],

FREQ1[7:0], and FREQ0[7:0].

Use the following equation to determine the data rate:

[]

()

)

(

RATE

SEL

REFCLK

DATARATE

FREQ

where:

FREQ[22:0] is the reading from FREQ2[6:0] (MSByte),

FREQ1[7:0], and FREQ0[7:0] (LSByte).

Table 13.

D22

D21...D17

D16

D15

D14...D9

D6...D1

FREQ2[6:0]

FREQ1[7:0]

FREQ0[7:0]

fDATARATE is the data rate (Mb/s).

fREFCLK is the REFCLK frequency (MHz).

SEL_RATE is the setting from CTRLA[7:6].

For example, if the reference clock frequency is 32 MHz,

SEL_RATE = 1, since the CTRLA[7:6] setting would be [01],

because the reference frequency would fall into the 25 MHz to

50 MHz range. Assume for this example that the input data rate

is 2.488 Gb/s (OC-48). After following Steps 1 through 4, the

value that is read back on FREQ[22:0] = 0x26E010, which is

equal to 2.5477 × 106. Plugging this value into the equation

yields

(

)

(

)

Gb/s

488

5477

)

(

If subsequent frequency measurements are required, CTRLA[1]

should remain set to 1. It does not need to be reset. The

measurement process is reset by writing a 1 followed by a 0 to

CTRLB[3]. This initiates a new data rate measurement. Follow

Steps 2 through 4 to read back the new data rate.

Note: A data rate readback is valid only if LOL is low. If LOL is

high, the data rate readback is invalid.

ADN2817 Scheda tecnica(PDF) 23 Page - Analog Devices

ADN2817 Scheda tecnica(HTML) 23 Page - Analog Devices

Html Pages

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35

Scheda tecnica Scarica

Link URL