SIM800L datasheet(27/73 Pages) SIMCOM

27 / 73 page

Smart Machine Smart Decision

SIM800H&SIM800L_Hardware Design_V2.02

2015-07-27

is set to minimum functionality by “AT+CFUN=0”, the RF function and SIM card function will be disabled. In

this case, the serial port is still accessible, but all AT commands correlative to RF function and SIM card

function will not be accessible.

For detailed information about AT command “AT+CFUN=<fun>“, please refer to document [1].

4.3.2.

Sleep Mode 1 (AT+CSCLK=1)

Customer can control SIM800H&SIM800L module to enter or exit the sleep mode (AT+CSCLK=1) by DTR

signal. When DTR is in high level and without interrupt (on air and hardware such as GPIO interrupt or data in

serial port), SIM800H&SIM800L will enter sleep mode automatically. In this mode, SIM800H&SIM800L can

still receive paging or SMS from network but the serial port is not accessible.

4.3.3.

Wake Up SIM800H&SIM800L from Sleep Mode 1

When SIM800H&SIM800L is in sleep mode 1(AT+CSCLK=1), the following methods can wake up the module:

Pull down DTR pin.

The serial port will be active after DTR pin is pulled to low level for about 50ms.

Receive a voice or data call from network.

Receive a SMS from network.

Receive external interrupt.

Note: After module has received incoming call or new SMS, serial port can report URC, but the serial port can not input AT

command. Only after the DTR pin is pulled to low level for 50ms, the serial port can input AT command.

4.3.4.

Sleep Mode 2 (AT+CSCLK=2)

In this mode, SIM800H&SIM800L will continuously monitor the serial port data signal. When there is no data

transfer over 5 seconds on the RXD signal and there is no on air and hardware interrupts (such as GPIO interrupt),

SIM800H&SIM800L will enter sleep mode 2 automatically. In this mode, SIM800H/L can still receive paging or

SMS from network .

4.3.5.

Wake Up SIM800H&SIM800L from Sleep Mode 2

When SIM800H&SIM800L is in sleep mode 2 (AT+CSCLK=2), the following methods can wake up the module:

Send data to SIM800H&SIM800L via main serial port (the first character will lose).

Receive a voice or data call from network.

Receive a SMS from network.

Note: Autobauding is default. It cannot enter sleep mode in the absence of synchronous serial port baud rate after module power

on.

4.4. RTC Backup

Current input for RTC when the VBAT is not supplied for the system. Current output for backup battery when

the VBAT power supply is in present and the backup battery is in low voltage state. The RTC power supply of

module can be provided by an external capacitor or a battery (non-chargeable or rechargeable) through the VRTC.

The following figures show various reference circuits for RTC back up.

SIM800L Scheda tecnica(PDF) 27 Page - SIMCom

SIM800L Scheda tecnica(HTML) 27 Page - SIMCom

Html Pages

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65 66 67 68 69 70 71 72 73

Scheda tecnica Scarica

Link URL