| Motore di ricerca datesheet componenti elettronici |
|
P83CE558 Scheda tecnica(PDF) 18 Page - NXP Semiconductors |
|
|
|||||||||||||||||||||||||||||
P83CE558 Scheda tecnica(HTML) 18 Page - NXP Semiconductors |
|
18 / 72 page ![]() Philips Semiconductors Preliminary specification P83CE558/P80CE558/P89CE558 Single-chip 8-bit microcontroller 1996 Aug 06 18 Figure 15. Functional diagram of AD converter. + – 8 8 8 8 2 2 10 10 10 COMPARATOR SAR DAC 8x 10–bit result registers SCAN LOGIC ADPSS ADCON 2 LATCHES Read ADRSH Read ADRSLn ANALOG Mux. ADC0 ADC7 AVref+ AVref– AVDD1 AVSS1 ADEXS INTERNAL BUS Table 10. Description of ADCON bits SYMBOL BIT FUNCTION ADCON.7 ADPR1 Control bit for the prescaler. ADCON.6 ADPR0 Control bit for the prescaler. ADPR1=0 ADPR0=0 Prescaler divides by 2 (default by reset) ADPR1=0 ADPR0=1 Prescaler divides by 4 ADPR1=1 ADPR0=0 Prescaler divides by 6 ADPR1=1 ADPR0=1 Prescaler divides by 8 ADCON.5 ADPOS ADPOS is reserved for future use. Must be ’0’ if ADCON is written. ADCON.4 ADINT ADC interrupt flag. This flag is set when all selected analog inputs are converted, as well in continuous scan as in one-time scan mode. An interrupt is invoked if this interrupt is enabled. ADINT must be cleared by software. It cannot be set by software. ADCON.3 ADSST ADC start and status. Setting this bit by software or by hardware (via ADEXS input) starts the A/D conversion of the selected analog inputs. ADSST stays a ‘one’ in continuous scan mode. In one-time scan mode, ADSST is cleared by hardware when the last selected analog input channel has been converted. As long as ADSST is ’1’, new start commands to the ADC-block are ignored. An A/D conversion in progress is aborted if ADSST is cleared by software. ADCON.2 ADCSA 1 = Continuous scan of the selected analog inputs after a start of an A/D conversion. 0 = One-time scan of the selected analog inputs after a start of an A/D conversion. ADCON.1 ADSRE 1 = A rising edge at input ADEXS will start the A/D conversion and generate a capture signal. 0 = A rising edge at input ADEXS has no effect. ADCON.0 ADSFE 1 = A falling edge at input ADEXS will start the A/D conversion and generate a capture signal. 0 = A falling edge at input ADEXS has no effect. |
|
Link URL |
| Lei ha avuto il aiuto da alldatasheet? [ DONATE ] |
Di alldatasheet | Richest di pubblicita | contatti | Privacy Policy | Collegamento alla scheda tecnica | scambio Link | Ricerca produttore All Rights Reserved©Alldatasheet.com |
| Russian : Alldatasheetru.com | Korean : Alldatasheet.co.kr | Spanish : Alldatasheet.es | French : Alldatasheet.fr | Italian : Alldatasheetit.com Portuguese : Alldatasheetpt.com | Polish : Alldatasheet.pl | Vietnamese : Alldatasheet.vn Indian : Alldatasheet.in | Mexican : Alldatasheet.com.mx | British : Alldatasheet.co.uk | New Zealand : Alldatasheet.co.nz |
|
Family Site : ic2ic.com |
icmetro.com |