TC510 datasheet(6/34 Pages) MICROCHIP

6 / 34 page

TC500/A/510/514

DS21428D-page 6

3.0

PIN DESCRIPTIONS

The descriptions of the pins are listed in Table 3-1.

TABLE 3-1:

PIN FUNCTION TABLE

Pin No.

Symbol

Function

TC500,

TC500A

TC510

TC514

CINT

Integrator output. Integrator capacitor connection.

Not Used

VSS

Negative power supply input (TC500/TC500A only).

CAZ

Auto-zero input. The auto-zero capacitor connection.

BUF

Buffer output. The Integrator capacitor connection.

ACOM

This pin is grounded in most applications. It is recommended that ACOM and the

input common pin (Ven- or CHn-) be within the analog Common Mode Range (CMR).

CREF-

Input. Negative reference capacitor connection.

CREF+ Input. Positive reference capacitor connection.

VREF-

Input. External voltage reference (-) connection.

VREF+ Input. External voltage reference (+) connection.

Not Used

VIN-

Negative analog input.

Not Used

VIN+

Positive analog input.

Input. Converter phase control MSB. (See input B.)

Input. Converter phase control LSB. The states of A, B place the

TC5XX in one of

four required phases. A conversion is complete when all four phases have been

executed:

Phase control input pins:

AB =

00: Integrator zero

01: Auto-zero

10: Integrate

11: De-integrate

CMPTR

OUT

Zero crossing comparator output. CMPTR is high during the integration phase when

a positive input voltage is being integrated and is low when a negative input voltage

is being integrated. A high-to-low transition on CMPTR signals the processor that the

De-integrate phase is completed. CMPTR is undefined during the auto-zero phase. It

should be monitored to time the integrator zero phase.

DGND

Input. Digital ground.

VDD

Input. Power supply positive connection.

—

CAP+

Input. Negative power supply converter capacitor (+) connection.

—

CAP-

Input. Negative power supply converter capacitor (-) connection.

—1

VOUT-

Output. Negative power supply converter output and reservoir capacitor connection.

This output can be used to power other devices in the circuit requiring a negative

bias voltage.

—

OSC

Oscillator control input. The negative power supply converter normally runs at a

frequency of 100 kHz. The converter oscillator frequency can be slowed down (to

reduce quiescent current) by connecting an external capacitor between this pin and

VDD (see Section 2.0 “Typical Performance Curves”).

—

CH1+

Positive analog input pin. MUX channel 1.

—

CH1-

Negative analog input pin. MUX channel 1.

—

CH2+

Positive analog input pin. MUX channel 2.

—

CH2-

Negative analog input pin. MUX channel 2.

—

CH3+

Positive analog input pin. MUX channel 3.

—

CH3-

Negative analog input pin. MUX channel 3.

—

CH4+

Positive analog input pin. MUX channel 4.

—

CH4-

Negative analog input pin. MUX channel 4

—

Multiplexer input channel select input LSB (see A1).

—

Multiplexer input channel select input MSB.

Phase control input pins: A1, A0 =

00 = Channel 1

01 = Channel 2

10 = Channel 3

11 = Channel 4

TC510 Scheda tecnica(PDF) 6 Page - Microchip Technology

TC510 Scheda tecnica(HTML) 6 Page - Microchip Technology

Html Pages

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34

Scheda tecnica Scarica

Link URL