 |
Motore di ricerca datesheet componenti elettronici |
|
|
Motore di ricerca datesheet componenti elettronici |
|
TUSB2E221 Scheda tecnica(PDF) 48 Page - Texas Instruments |
|
|
|||||||||||||||||||||||||||||
TUSB2E221 Scheda tecnica(HTML) 48 Page - Texas Instruments |
|
|
48 / 65 page  Table 9-26. GLOBAL_CONFIG Register Field Descriptions (continued) Bit Field Type Reset Description 5 DISABLE_P0 R/W 0h Disabled Mode Repeater 0 (I2C will remain Active) (If port is not disconnected, wait until disconnect event to disable the repeater) 0h = Repeater Enabled 1h = Repeater Disabled 4 INT_OUT_TYPE R/W 0h INT Output Type INT output drive strength in open drain mode will be the same as GPIO setting 0h = Open Drain 1h = push pull 3 INT_POLARITY R/W 0h INT pin polarity in push-pull mode only (open drain mode will always be Active low) 0h = Active High (only for push-pull) 1h = Active Low (only for push-pull, open drain will always be active low) 2 RESERVED R/W 0h Reserved 1-0 RESERVED R 0h Reserved 9.1.25 INT_ENABLE_1 Register (Offset = B3h) [Reset = 00h] INT_ENABLE_1 is shown in Table 9-27. Return to the Summary Table. Table 9-27. INT_ENABLE_1 Register Field Descriptions Bit Field Type Reset Description 7 GPIO1_RISING_EDGE R/W 0h INT_GPIO1_RISING_EDGE enable. When GPIO1_IN_TRIGGER_TYPE = 0 (Edge), this enables interrupt on Rising Edge of GPIO1. When GPIO1_IN_TRIGGER_TYPE = 1 (Level), this enables Interrupt when GPIO1 = High. 0h = Not Enabled 1h = Enabled 6 GPIO1_FALLING_EDGE R/W 0h INT_GPIO1_FALLING_EDGE enable. When GPIO1_IN_TRIGGER_TYPE = 0 (Edge), this enables interrupt on Falling Edge of GPIO1. When GPIO1_IN_TRIGGER_TYPE = 1 (Level), this enables Interrupt when GPIO1 = Low. 0h = Not Enabled 1h = Enabled 5 GPIO0_RISING_EDGE R/W 0h INT_GPIO0_RISING_EDGE enable. When GPIO0_IN_TRIGGER_TYPE = 0 (Edge), this enables interrupt on Rising Edge of GPIO0. When GPIO0_IN_TRIGGER_TYPE = 1 (Level), this enables Interrupt when GPIO0 = High. 0h = Not Enabled 1h = Enabled 4 GPIO0_FALLING_EDGE R/W 0h INT_GPIO0_FALLING_EDGE enable. When GPIO0_IN_TRIGGER_TYPE = 0 (Edge), this enables interrupt on Falling Edge of GPIO0. When GPIO0_IN_TRIGGER_TYPE = 1 (Level), this enables Interrupt when GPIO0 = Low. 0h = Not Enabled 1h = Enabled 3 USB_REMOTE_WAKE_P 1 R/W 0h INT_USB_REMOTE_WAKE_P1 enable. See L2 State Interrupt Modes 0h = Not Enabled 1h = Enabled TUSB2E221 SNLS757B – JUNE 2024 – REVISED NOVEMBER 2024 www.ti.com 48 Submit Document Feedback Copyright © 2024 Texas Instruments Incorporated Product Folder Links: TUSB2E221 |
|
Link URL |
| Lei ha avuto il aiuto da alldatasheet? [ DONATE ] |
Di alldatasheet | Richest di pubblicita | contatti | Privacy Policy | Collegamento alla scheda tecnica | scambio Link | Ricerca produttore All Rights Reserved©Alldatasheet.com |
| Russian : Alldatasheetru.com | Korean : Alldatasheet.co.kr | Spanish : Alldatasheet.es | French : Alldatasheet.fr | Italian : Alldatasheetit.com Portuguese : Alldatasheetpt.com | Polish : Alldatasheet.pl | Vietnamese : Alldatasheet.vn Indian : Alldatasheet.in | Mexican : Alldatasheet.com.mx | British : Alldatasheet.co.uk | New Zealand : Alldatasheet.co.nz |
|
Family Site : ic2ic.com |
icmetro.com |
Italian ▼
English
Chinese
German
Japanese
Russian
Korean
Spanish
French
Italian
Portuguese
Polish
Vietnamese
Indian
Mexican
British
New Zealand
