LMP7721

SNOSAW6E – JANUARY 2008 – REVISED DECEMBER 2014

www.ti.com

Electrical Characteristics: 2.5 V (continued)

Unless otherwise specified, all limits are specified for TA = 25°C, V

+ = 2.5 V, V− = 0 V, V

CM = (V

+ + V−)/2.

PARAMETER

TEST CONDITIONS

MIN(1)

TYP(2)

MAX(1)

UNIT

In

Input-Referred Current Noise

f = 1 kHz

0.01

pA/

THD+N

Total Harmonic Distortion +

f = 1 kHz, AV = 2, RL = 100 kΩ

0.003%

Noise

VO = 0.9 VPP

f = 1 kHz, AV = 2, RL = 600 Ω

0.003%

VO = 0.9 VPP

6.6 Electrical Characteristics: 5 V

Unless otherwise specified, all limits are specified for TA = 25°C, V

+ = 5 V, V− = 0 V, V

CM = (V

+ + V−)/2.

PARAMETER

TEST CONDITIONS

MIN(1)

TYP(2)

MAX(1)

UNIT

VOS

Input Offset Voltage

–150

±26

150

μV

–40°C

≤ TJ ≤ 125°C

450

450

TC VOS

Input Offset Average Drift

–1.5

–4

μV/°C

(3)

IBIAS

Input Bias Current

VCM = 1 V

(4) (5)

25°C

–20

±3

20

fA

−40°C to 85°C

–900

900

−40°C to 125°C

–5

5

pA

IOS

Input Offset Current

(5)

±6

±40

fA

CMRR

Common-Mode Rejection Ratio

0 V

≤ VCM ≤ 3.7 V

84

100

dB

0 V

≤ VCM ≤ 3.7 V, –40°C ≤ TJ ≤ 125°C

82

PSRR

Power Supply Rejection Ratio

1.8 V

≤ V+ ≤ 5.5 V, V− = 0 V, VCM = 0

84

96

dB

1.8 V

≤ V+ ≤ 5.5 V, V− = 0 V, VCM = 0,

80

–40°C

≤ TJ ≤ 125°C

CMVR

Input Common-Mode Voltage

CMRR

≥ 80 dB

−0.3

4

V

Range

CMRR

≥ 78 dB, –40°C ≤ TJ ≤ 125°C

–0.3

4

AVOL

Large Signal Voltage Gain

VO = 0.3 V to 4.7 V, RL = 2 kΩ to V

+/2

88

111

VO = 0.3 V to 4.7 V, RL = 2 kΩ to V

+/2,

82

–40°C

≤ TJ ≤ 125°C

dB

VO = 0.3 V to 4.7 V, RL = 10 kΩ to V

+/2

92

120

VO = 0.3 V to 4.7 V, RL = 10 kΩ to V

+/2,

88

–40°C

≤ TJ ≤ 125°C

VO

Output Swing High

RL = 2 kΩ to V

+/2

70

30

RL = 2 kΩ to V

+/2, –40°C ≤ T

J ≤ 125°C

77

mV

from V+

RL = 10 kΩ to V

+/2

60

20

RL = 10 kΩ to V

+/2, –40°C ≤ T

J ≤ 125°C

66

Output Swing Low

RL = 2 kΩ to V

+/2

31

70

RL = 2 kΩ to V

+/2, –40°C ≤ T

J ≤ 125°C

73

mV

RL = 10 kΩ to V

+/2

20

60

RL = 10 kΩ to V

+/2, –40°C ≤ T

J ≤ 125°C

62

(1)

Limits are 100% production tested at 25°C. Limits over the operating temperature range are specified through correlations using the

Statistical Quality Control (SQC) method.

(2)

Typical values represent the most likely parametric norm as determined at the time of characterization. Actual typical values may vary

over time and will also depend on the application and configuration. The typical values are not tested and are not specified on shipped

production material.

(3)

Offset voltage average drift is determined by dividing the change in VOS at the temperature extremes by the total temperature change.

(4)

Positive current corresponds to current flowing into the device.

(5)

This parameter is specified by design and/or characterization and is not tested in production.

6

Submit Documentation Feedback

Copyright © 2008–2014, Texas Instruments Incorporated

Product Folder Links: LMP7721