Motore di ricerca datesheet componenti elettronici
  Italian  ▼
ALLDATASHEETIT.COM

X  

LNBH24 Scheda tecnica(PDF) 10 Page - STMicroelectronics

Il numero della parte LNBH24
Spiegazioni elettronici  Dual LNB supply and control IC with step-up and I2C interface
PDF  30 Pages
Scroll/Zoom Zoom In 100%  Zoom Out
Produttore elettronici  STMICROELECTRONICS [STMicroelectronics]
Homepage  http://www.st.com
Logo STMICROELECTRONICS - STMicroelectronics

LNBH24 Scheda tecnica(HTML) 10 Page - STMicroelectronics

Back Button LNBH24 Datasheet HTML 6Page - STMicroelectronics LNBH24 Datasheet HTML 7Page - STMicroelectronics LNBH24 Datasheet HTML 8Page - STMicroelectronics LNBH24 Datasheet HTML 9Page - STMicroelectronics LNBH24 Datasheet HTML 10Page - STMicroelectronics LNBH24 Datasheet HTML 11Page - STMicroelectronics LNBH24 Datasheet HTML 12Page - STMicroelectronics LNBH24 Datasheet HTML 13Page - STMicroelectronics LNBH24 Datasheet HTML 14Page - STMicroelectronics Next Button
Zoom Inzoom in Zoom Outzoom out
 10 / 30 page
background image
Pin configuration
LNBH24
10/30
Pin n°
(sec. A/B)
Symbol
Name
Function
18
TTX-A
TTX enable
The TTX pins can be used as well as the TTX I2C bits of the
system register, to control the TTX function enable.
Set floating or to GND if not used.
2TTX-B
17
DETIN-A
Tone decoders
inputs
22 kHz tone decoders inputs must be AC coupled to the
DiSEqC 2.0 BUS. Set to GND if not used.
3DETIN-B
15
DSQOUT- A
DiSEqC outputs
Open drain outputs of the tone detectors to the main
µController for DiSEqC 2.0 data decoding. They are LOW
when tone is detected on DETIN pins. Set to GND if not used.
5
DSQOUT- B
19
EXTM-A
External
modulation
External modulation logic input pins which activate the 22 kHz
tone output on the VoTX pins. Set to ground if not used.
36
EXTM-B
10
P-GND-A
Power grounds
DC-DC converters power grounds.
9
P-GND-B
ePad
ePad
Exposed Pad
To be connected with power grounds and to the ground layer
through vias to dissipate the heat.
1, 30
A-GND
Analog grounds
Analog circuits grounds.
27
BYP
By-pass capacitor
Needed for internal pre-regulator filtering. The BYP pin is
intended only to connect an external ceramic capacitor. Any
connection of this pin to external current or voltage sources
may cause permanent damage to the device.
14
ADDR-A
Address setting
Two I²C addresses available for each section by setting the
Address pins voltage level. See Table 10
6
ADDR-B
21
ISEL-A
Current selection
The resistors “RSEL” connected between ISEL and GND
define the linear regulators current limit protection threshold
by the equation: IMAX(typ)=10000/ RSEL.
34
ISEL-B
20
VCTRL-A
Output voltage
control
13 V-18 V linear regulators VoRX switch control. To be used
only with VSEL=1. If VCTRL=1 or floating VoRX=18.5 V (or
19.5V if LLC=1). If VCTRL=0 than VoRX=13.4 V (LLC=either 0
or 1). Leave floating if not used. DO NOT connect to GND if
not used.
35
VCTRL-B
7, 23, 24
N.C.
Not connected
Not internally connected pins.
Table 2.
Pin description (continued)



Html Pages

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30


Scheda tecnica Scarica

Go To PDF Page


Link URL



Lei ha avuto il aiuto da alldatasheet?  [ DONATE ] 

Di alldatasheet   |   Richest di pubblicita   |   contatti   |   Privacy Policy   |   Collegamento alla scheda tecnica    |   scambio Link   |   Ricerca produttore
All Rights Reserved©Alldatasheet.com


Mirror Sites
English : Alldatasheet.com  |   English : Alldatasheet.net  |   Chinese : Alldatasheetcn.com  |   German : Alldatasheetde.com  |   Japanese : Alldatasheet.jp
Russian : Alldatasheetru.com  |   Korean : Alldatasheet.co.kr  |   Spanish : Alldatasheet.es  |   French : Alldatasheet.fr  |   Italian : Alldatasheetit.com
Portuguese : Alldatasheetpt.com  |   Polish : Alldatasheet.pl  |   Vietnamese : Alldatasheet.vn
Indian : Alldatasheet.in  |   Mexican : Alldatasheet.com.mx  |   British : Alldatasheet.co.uk  |   New Zealand : Alldatasheet.co.nz
Family Site : ic2ic.com  |   icmetro.com