DS-0387 / DCN 11179 / Rev B

All Sensors

Prime Grade Performance Characteristics

How to Order

-

-

-

-

Product Series

Coating

P

N

Package Selection

Pressure Ranges

L04D

015A

L04G

L10D

030A

L10G

0.3D

100A

0.3G

001D

001G

005D

005G

015D

015G

030D

030G

100D

100G

Grades

P

H

C

± 100 PSI

Parylene Coating

No Parylene Coating

CFFD

± 30 PSI

0 to 30 PSI

0 to 30 PSI

Millivolt Output Low

Pressure Series

Differential

Absolute

Gage

ACPC

L04D

P

CFFD

± 15 PSI

0 to 15 PSI

± 4 inH2O

0 to 4 inH2O

± 10 inH2O

0 to 10 inH2O

± 0.3 PSI

0 to 0.3 PSI

0 to 100 PSI

N

± 1 PSI

0 to 1 PSI

± 5 PSI

0 to 5 PSI

ACPC

0 to 15 PSI

CPPD

DIP

SIP

CFFS

CFNS

CPFS

CPNS

CPPS

Prime Grade

H-Grade

C-Grade

CPFD

CPND

CFND

0 to 100 PSI

Parameter

Note 1

Min

Typ

Max

Units

Notes

Output Span

0.3 PSI, 10 inH2O

19.00

20.00

21.00

mV

4

1 PSI

17.82

18.00

18.18

mV

4

5 PSI

59.40

60.00

60.60

mV

4

15 PSI, 15 PSIA, 30 PSI, 30 PSIA

89.10

90.00

90.90

mV

4

100 PSI, 100 PSIA

99.00

100.00

101.00

mV

4

Offset Voltage (@ Zero Diff. Pressure)

0.3 PSI, 10 inH2O, 1 PSI, 5 PSI, 15 PSI, 30 PSI, 100 PSI

-

-

±0.30

mV

-

15 PSIA, 30 PSIA, 100 PSIA

-

-

±0.50

mV

-

Offset Temperature Shift (0°C-70°C)

-

-

±250

uV

2

Linearity, Hysteresis Error

0.3 PSI, 10 inH2O, 1 PSI, 5 PSI

-

0.10

±0.25

%FSS

3

15 PSIA

-

0.10

±0.30

%FSS

3

15 PSI, 30 PSI, 30 PSIA, 100 PSI, 100 PSIA

-

0.15

±0.30

%FSS

3

Span Temperature Shift

-

-

±1.00

%FSS

2

Specification Notes

note

1: All pArAmeters Are meAsured At 12.0 volt excitAtion, for the nominAl full scAle pressure And room temperAture unless otherwise specified. pressure

meAsurements Are with positive pressure Applied to

port B. sensors Are rAtiometric to supply voltAge.

note

2: shift is relAtive to 25°c.

note

3: meAsured At one-hAlf full scAle rAted pressure using Best strAight line curve fit.

note

4: the spAn is the AlgerBrAic difference Between full scAle output voltAge And the offset voltAge.

note

5: pArylene coAting is only AvAilABle for pressure rAnges ABove 10 inh2o.

Pressure resPonse:

for Any pressure Applied, the response time to get to 90% of pressure Applied is typicAlly less thAn 100 useconds.

Note: Parylene Coating is only available for pressure ranges above 10 inH2O.

Page 5 of 11