| Motore di ricerca datesheet componenti elettronici |
|
DLP-232PC Scheda tecnica(PDF) 5 Page - THAT Corporation All rights reserved. |
|
|
|||||||||||||||||||||||||||||
DLP-232PC Scheda tecnica(HTML) 5 Page - THAT Corporation All rights reserved. |
|
5 / 20 page ![]() THAT 626x DEMO Datasheet Page 5 of 20 Document 600194 Rev 00 THAT Corporation; 45 Sumner Street; Milford, MA 01757-1656; USA Tel: +1 508 478 9200; Fax: +1 508 478 0990; Web: www.thatcorp.com Copyright © 2018, THAT Corporation; All rights reserved Power Bipolar vs. Unipolar Operation The THAT626x family of parts have the ability to be powered from a bipolar supply (± 5 V typical) or from a unipolar supply (+10 V typical). In Unipolar mode, Vad, the ADC driver supply, is generated from an on-board +5 V regulator. This capability allows the 626x to easily fit a variety of applications ranging from professional portable recorders to POE (Power over Ethernet) installations. While operation in either mode is straightforward, with very similar performance specifications, there are a few important differences that should be brought to your attention when considering the power supply options. 1) Clamp Diodes: The clamp diodes, (D102, D103, D104, and D105 on the IC Module) which are used to prevent exceeding the Common-Mode input range of the ADC driver, are only required for bipolar operation. These 4 diodes and the associated Vclmp voltage divider network are not required in unipolar mode and can be eliminated in the final product design. These diodes do no harm in unipolar mode and the demo board leaves them connected in both modes for simplicity. 2) ADC Driver Vcm voltage: The optimum ADC Driver VCM voltage required in order to insure that the driver can swing the full 2 Vrms is +2.5 V in bipolar mode and +3.1 V in unipolar mode. This voltage is automatically switched using the Voltage Select Module. The demonstration system provides both dc and ac coupled outputs on three pin headers for driving ADCs. We recommend using the dc outputs in bipolar mode and the ac outputs in unipolar mode. Please refer to the 626x data sheet for a detailed discussion concerning the optimum VCM operating conditions. 3) Polarized capacitor orientation: In unipolar mode, the 626x’s inputs are biased at +5 V and the resulting bias across the input coupling capacitors (C13, C19, C32, and C42) changes polarity depending on the state of the phantom power switch. Also, the inter-stage coupling capacitors on the IC Module (C2, C3, C22, and C23) are biased in opposite directions depending on bipolar or unipolar operation. For this reason, you will notice that the aforementioned capacitors used in the demonstration system are of the Non-Polar (NP) type. In the case of C2, C3, C22 and C23 this was done for convenience and more cost effective fixed polarity capacitors can be used in your final design depending on the specifics of your application. On Board Regulators and Phantom Power The demonstration system requires a ± 5 V (± 5.5 V max) external power supply for bipolar mode operation or a single +10 V (+11.0 max) supply for unipolar operation. The on-board +5 V regulator is used in unipolar mode in order to provide +5 V required to power the ADC driver stage. The USB interface (U3) runs on USB bus power, supplied by the host PC. An external+48 V phantom power supply can also be used for powering microphones if desired. Phantom power is activated by the switch SW1 and the associated LED will light up when active. Note, the LED will not light in either switch position if the external 48 V is not connected. The ground return for +48 V phantom power is via the chassis ground and connects to the Analog ground via the zero ohm resistor R80. The +5 V input (or the output of the internal 5 V regulator) is regulated on board to the 3.3 V required for the digital logic. Audio Inputs The Neutrik combo connector accepts an XLR or ¼" TRS cable. The 1/4" TRS signal path includes a 10 dB pad in order to support line level inputs up to +26.5dBu. The input impedance is 3.02k at the XLR inputs and 10k looking in from the ¼” inputs. Pads for an additional shunt resistor (R100 and R101) have been provided across the inputs in order to easily facilitate input impedance modifications. ADC Driver Outputs The demo board is assembled with the driver output configured in accordance with the filter configuration often recommended by the ADC manufactures. This includes a 90.9 ohm resistor inside the driver feedback loop (R7, R12, R23, and R32), located on the pre- amp/ADC module and a 680 pF feedback capacitor (C9, C15, C29, and C35), also located on the preamp/ ADC module. Pads have also been included on the mother board for the typically recommended 2.7nF shunt capacitor. This shunt capacitor should be located as close as possible to the actual ADC converter’s input pins if using the 626x demonstration system to drive a converter for your test measurements. When using the demonstration system without a converter, the pads provide a convenient location for the capacitor when making filter measurements. A zero ohm resistor (R11, R15, R29 and R33) has been placed in series with the 3-pin output headers on the motherboard in order to provide a convenient means for implementing alternate output filter configurations. There is also a prototyping area available on the board if more substantial output filtering modifications are required for your particular ADC. There are two 3-pin output headers on each channel, one is dc coupled for use in bipolar mode, while the other is ac coupled for use in the unipolar mode. Please note that the XLR output is ac coupled and has a 49.9 ohm series resistor for isolation. This XLR output is intended to drive your general purpose test equipment. VCM IN The demo board provides the option for biasing the ADC driver outputs directly from the ADC’s common- mode reference voltage via the VCM IN header (P15). Please note that reference voltage available on most Connections |
|
|
Link URL |
| Lei ha avuto il aiuto da alldatasheet? [ DONATE ] |
Di alldatasheet | Richest di pubblicita | contatti | Privacy Policy | Collegamento alla scheda tecnica | scambio Link | Ricerca produttore All Rights Reserved©Alldatasheet.com |
| Russian : Alldatasheetru.com | Korean : Alldatasheet.co.kr | Spanish : Alldatasheet.es | French : Alldatasheet.fr | Italian : Alldatasheetit.com Portuguese : Alldatasheetpt.com | Polish : Alldatasheet.pl | Vietnamese : Alldatasheet.vn Indian : Alldatasheet.in | Mexican : Alldatasheet.com.mx | British : Alldatasheet.co.uk | New Zealand : Alldatasheet.co.nz |
|
Family Site : ic2ic.com |
icmetro.com |