| Motore di ricerca datesheet componenti elettronici |
|
ADE7761BARSZ Scheda tecnica(PDF) 20 Page - Analog Devices |
|
|
|||||||||||||||||||||||||||||
ADE7761BARSZ Scheda tecnica(HTML) 20 Page - Analog Devices |
|
20 / 24 page ![]() ADE7761B Rev. 0 | Page 20 of 24 Missing Neutral Gain Calibration Example When the ADE7761B is in missing neutral mode, the energy is billed based on the active current input signal level. The frequency outputs in this mode can be calibrated with the MISCAL analog input pin. In this mode, applying a dc voltage of 330 mV on MISCAL is equivalent to applying, in normal mode, a pure sine wave on the voltage input with a peak value of 330 mV. The MISCAL input can vary from 0 V to 660 mV (see the Analog Inputs section). When set to 0 V, the frequency outputs are close to zero. When set to 660 mV dc, the frequency outputs are twice that when MISCAL is at 330 mV dc. In other words, Equation 7 can be used in missing neutral mode by replacing V2rms by MISCALrms /√2. In normal mode, ac voltages of ±330 mV peak are applied to Channel V1 and Channel V2, and then the expected output frequency on F1 and F2 is calculated as follows: Gain =1; PGA =0 F1–4 = 1.7 Hz, SCF = S1 = S0 = 0 V1 = rms of 330 mV peak ac = 0.33/√2 V V2 = rms of 330 mV peak ac = 0.33/√2 V VREF = 2.5 V (nominal reference value) Hz 0917 . 0 5 . 2 2 2 Hz 7 . 1 33 . 0 33 . 0 13 . 6 , 2 2 1 = × × × × × = Frequency F F 2 2 1 2 / 1 13 . 6 , REF 4 1 rms rms V f MISCAL V Gain Frequency F F − × × × × = (8) CF Frequency = F1, F2 Frequency × 64 = 5.87 Hz In missing neutral mode, the ac voltage of ±330 mV peak is applied to Channel V1, no signal is connected on Channel V2, and a 330 mV dc input is applied to MISCAL. With the ADE7761B in the same configuration as the previous example, the expected output frequencies on CF, F1, and F2 are where: F1 , F2 Frequency is the output frequency on F1 and F2 (Hz). Gain is 1 or 16, depending on the PGA gain selection made using Logic Input PGA. V1rms is the differential rms voltage signal on Channel V1 (V). MISCALrms is the differential rms voltage signal on the MISCAL pin (V). VREF is the reference voltage (2.5 V ± 8%) (V). f1-4 is one of four possible frequencies selected by using Logic Input S0 and Logic Input S1 (see Table 6). Hz 0917 . 0 5 . 2 2 Hz 7 . 1 2 / 33 . 0 33 . 0 13 . 6 , 2 = × × × × = Frequency F F 2 1 CF Frequency = F1, F2 Frequency × 64 = 5.87 Hz |
|
|
Link URL |
| Lei ha avuto il aiuto da alldatasheet? [ DONATE ] |
Di alldatasheet | Richest di pubblicita | contatti | Privacy Policy | Collegamento alla scheda tecnica | scambio Link | Ricerca produttore All Rights Reserved©Alldatasheet.com |
| Russian : Alldatasheetru.com | Korean : Alldatasheet.co.kr | Spanish : Alldatasheet.es | French : Alldatasheet.fr | Italian : Alldatasheetit.com Portuguese : Alldatasheetpt.com | Polish : Alldatasheet.pl | Vietnamese : Alldatasheet.vn Indian : Alldatasheet.in | Mexican : Alldatasheet.com.mx | British : Alldatasheet.co.uk | New Zealand : Alldatasheet.co.nz |
|
Family Site : ic2ic.com |
icmetro.com |