ADE5169 datasheet(96/148 Pages) AD

96 / 148 page

ADE5166/ADE5169

Rev. 0 | Page 96 of 148

BLINK MODE

Blink mode is enabled by setting the BLINKEN bit (Bit 5) in the

LCD configuration SFR (LCDCON, Address 0x95). This mode

is used to alternate between the LCD on state and LCD off state

so that the LCD screen appears to blink. There are two blinking

modes: a software controlled blink mode and an automatic

blink mode.

Software Controlled Blink Mode

The LCD blink rate can be controlled by user code with the

BLKMOD bits (Bits[7:6]) in the LCD clock SFR (LCDCLK,

Address 0x96) by toggling the bits to turn the display on and off

at a rate determined by the MCU code.

Automatic Blink Mode

There are five blink rates. These blink rates are selected by the

BLKMOD bits (Bits[7:6]) and the BLKFREQ bits (Bits[5:4]) bits

in the LCD clock SFR (LCDCLK, Address 0x96); see Table 94.

SCROLLING MODE

The ADE5166/ADE5169 provide the possibility to have four

screens in memory. The LCD driver can use any of these screens

by setting the SCREEN_SEL bits in the LCD Configuration Y SFR

(LCDCONY, Address 0xB1) and clearing the refresh bit (Bit 0)

in the same register. The software scrolling of the screens can

then be achieved by a one-command instruction.

Automatic Scrolling Mode

The ADE5166/ADE5169 also provide an automatic scrolling

between the screens using the five available blink rates. This

mode is enabled by setting bit AUTOSCREENSCROLL (Bit 7)

in the LCD Configuration Y SFR (LCDCONY, Address 0xB1)

and also the BLINKEN bit (Bit 5) in the LCD configuration SFR

(LCDCON, Address 0x95). To allow the scrolling frequency to

be selected, the BLKMOD bits (Bits[7:6]) in the LCD clock SFR

(LCDCLK, Address 0x96) should both be set to 1. The scrolling

rates are then selected by the BLKFREQ bits (Bits[5:4]) in the

LCD clock SFR (LCDCLK, Address 0x96); see Table 94. Auto-

matic scrolling mode is available in all operating modes.

DISPLAY ELEMENT CONTROL

Four banks of 15 bytes of data memory located in the LCD module

control the on or off state of each segment of the LCD. The LCD

data memory is stored in Address 0 through Address 14 in the

LCD module, with two extra bits defining which one of the four

screens is being addressed.

Each byte configures the on and off states of two segment lines.

The LSBs store the state of the even numbered segment lines,

and the MSBs store the state of the odd numbered segment lines.

For example, LCD Data Address 0 refers to segment Line 1 and

Line 0 (see Table 101). Note that the LCD data memory is

maintained in the PSM2 operating mode.

The LCD data memory is accessed indirectly through the LCD

pointer SFR (LCDPTR, Address 0xAC) and LCD data SFR

(LCDDAT, Address 0xAE). Moving a value to the LCDPTR SFR

selects the LCD screen and data byte to be accessed and initiates

a read or write operation (see Table 98).

Writing to LCD Data Registers

To update the LCD data memory, first set the LSB of the LCD

Configuration Y SFR (LCDCONY, Address 0xB1) to freeze the

data being displayed on the LCD while updating it. This operation

ensures that the data displayed on the screen does not change

while the data is being changed. Then, move the data to the

LCD data SFR (LCDDAT, Address 0xAE) prior to accessing the

LCD pointer SFR (LCDPTR, Address 0xAC). The address of the

LCD screen should be consistent with the data changed. When the

MSB of the LCD pointer SFR (LCDPTR, Address 0xAC) is set, the

content of the LCD data SFR (LCDDAT, Address 0xAE) is trans-

ferred to the internal LCD data memory designated by the address

in the LCD pointer SFR (LCDPTR, Address 0xAC) and the

screen designator. Clear the LSB of the LCD Configuration Y SFR

(LCDCONY, Address 0xB1) when all of the data memory has been

updated to allow the use of the new LCD setup for display.

Sample 8052 code to update the segments attached to Pin FP10

and Pin FP11 on Screen 1 is as follows:

ORL

LCDCONY,#01h

;start updating the data

MOV

LCDDAT,#FFh

MOV

LCDPTR,#80h OR 05h

ANL

LCDCONY,#0FEh ;update finished

Reading LCD Data Registers

When the MSB of the LCD pointer SFR (LCDPTR, Address 0xAC)

is cleared, the content of the LCD data memory of the correspond-

ing screen designated by LCDPTR is transferred to the LCD data

SFR (LCDDAT, Address 0xAE).

Sample 8052 code to read the contents of LCD Data Memory

Address 0x07 on Screen 1, which holds the on and off state of

the segments attached to FP14 and FP15, is as follows.

MOV

LCDPTR,#07h

MOV

R1, LCDDAT

ADE5169 Scheda tecnica(PDF) 96 Page - Analog Devices

ADE5169 Scheda tecnica(HTML) 96 Page - Analog Devices

Html Pages

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65 66 67 68 69 70 71 72 73 74 75 76 77 78 79 80 81 82 83 84 85 86 87 88 89 90 91 92 93 94 95 96 97 98 99 100 ...More

Scheda tecnica Scarica

Link URL