Motore di ricerca datesheet componenti elettronici
  Italian  ▼
ALLDATASHEETIT.COM

X  

E7804 Scheda tecnica(PDF) 21 Page - Semtech Corporation

Il numero della parte E7804
Spiegazioni elettronici  133 MHZ Quad Pin Electronics Driver and Window Comparator
PDF  41 Pages
Scroll/Zoom Zoom In 100%  Zoom Out
Produttore elettronici  SEMTECH [Semtech Corporation]
Homepage  http://www.semtech.com
Logo SEMTECH - Semtech Corporation

E7804 Scheda tecnica(HTML) 21 Page - Semtech Corporation

Back Button E7804 Datasheet HTML 17Page - Semtech Corporation E7804 Datasheet HTML 18Page - Semtech Corporation E7804 Datasheet HTML 19Page - Semtech Corporation E7804 Datasheet HTML 20Page - Semtech Corporation E7804 Datasheet HTML 21Page - Semtech Corporation E7804 Datasheet HTML 22Page - Semtech Corporation E7804 Datasheet HTML 23Page - Semtech Corporation E7804 Datasheet HTML 24Page - Semtech Corporation E7804 Datasheet HTML 25Page - Semtech Corporation Next Button
Zoom Inzoom in Zoom Outzoom out
 21 / 41 page
background image
2
TEST AND MEASUREMENT PRODUCTS
© 2007 Semtech Corp. / Rev. 7, 02/26/07
E7804
www.semtech.com
Circuit Description (continued)
Register Name Set0_switches_&_states
Function Address
0x00
Set Select Bit
1
Channel/Set Address 0x00
Mode
Write Only
Channel Select Bit
1
Default Value
0 0000 0000 0000
0x00
Description
Register Name Set1_switches_&_states
Function Address
0x00
Set Select Bit
1
Channel/Set Address 0x01
Mode
Write Only
Channel Select Bit
1
Default Value
0 0000 0000 0000
0x00
Description
Register Name Set7_switches_&_states
Function Address
0x00
Set Select Bit
1
Channel/Set Address 0x01
Mode
Write Only
Channel Select Bit
1
Default Value
0 0000 0000 0000
0x00
Description
Set Functions
This register is used for controlling the Set_0 (CH0) switches on any channel that has been assigned to Set_1. Bits are
also present to control the channels' driver states. See the bit definitions to the Set0_relays_&_states for bit definitions.
Sets 2 through 6
This register is used for controlling the Set_7 (CH0) switches on any channel that has been assigned to Set_7. Bits are
also present to control the channels' driver states. See the bit definitions to the Set0_relays_&_states for bit definitions.
D3 – S4 – writing a one to this bit will close the switches that connect both the external PMU bus sense (EPMUS) and
force (EPMUF) lines to the channel's POUT pin.
D4 – S5 – writing a one to this bit will close the switch that connects the continuity test circuit (CTC) to the channel's
POUT pin.
D5 – S6 – writing a one to this bit will close the switch that connects the pull-up resistor and voltage to the channel's
POUT pin.
D6 – SDHI (Serial Data Hi) – writing a logical one to this bit will force the channel's driver to output the DVH voltage.
Writing a zero to this bit will force the driver to output the DVL voltage. The SDHI bit will only have effect if the SEN bit
(D8) in this register is set to a logical one, allowing the SDHI bit to override the state of the external DHI signal to this
channel's driver.
D7 – SDEN (Serial Data Enable) – writing a logical one to this bit will enable the channel's driver to output either DVH or
DVL (based on the SDHI bit). Writing a zero to this bit disables the driver output to high impedance. The SDEN bit will
only have effect if the SEN bit (D8) in this register is set to a logical 1, allowing the SDEN bit to override the state of the
external DEN signal to this channel's driver.
This register is used for controlling the Set_0 (CH0) switches on any channel that has been assigned to Set_0. Bits are
also present to control the channels' driver states.
D8 – SEN (Serial Enable) – writing this bit to a logical one will allow the D6 and D7 bits in this register override the
external driver control signals DHI and DEN.
D0 – S1 – writing a one to this bit will close the switch that connects the driver output to the channel's VIO pin.
D1 – S2 – writing a one to this bit will close the switch that connects the window comparator input to the channel's VIO
pin.
D2 – S3 – writing a one to this bit will close the switch that connects the driver output to the external PMU sense line
(EPMUS) for purposes of system diagnostics.



Html Pages

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41


Scheda tecnica Scarica

Go To PDF Page


Link URL



Lei ha avuto il aiuto da alldatasheet?  [ DONATE ] 

Di alldatasheet   |   Richest di pubblicita   |   contatti   |   Privacy Policy   |   Collegamento alla scheda tecnica    |   scambio Link   |   Ricerca produttore
All Rights Reserved©Alldatasheet.com


Mirror Sites
English : Alldatasheet.com  |   English : Alldatasheet.net  |   Chinese : Alldatasheetcn.com  |   German : Alldatasheetde.com  |   Japanese : Alldatasheet.jp
Russian : Alldatasheetru.com  |   Korean : Alldatasheet.co.kr  |   Spanish : Alldatasheet.es  |   French : Alldatasheet.fr  |   Italian : Alldatasheetit.com
Portuguese : Alldatasheetpt.com  |   Polish : Alldatasheet.pl  |   Vietnamese : Alldatasheet.vn
Indian : Alldatasheet.in  |   Mexican : Alldatasheet.com.mx  |   British : Alldatasheet.co.uk  |   New Zealand : Alldatasheet.co.nz
Family Site : ic2ic.com  |   icmetro.com