ATA5423-PLSW datasheet(71/100 Pages) ATMEL

71 / 100 page

4841D–WIRE–10/07

ATA5423/ATA5425/ATA5428/ATA5429

2.12

System outband

3rd

-order input intercept

point

∆f

meas1 = 1.8 MHz

∆f

meas2 = 3.6 MHz

RF = 315 MHz

(4)

IIP3

–22

dBm

RF = 345 MHz

(4)

IIP3

–22

dBm

RF = 433.92 MHz

(4)

IIP3

–21

dBm

RF = 868.3 MHz

(4)

IIP3

–17

dBm

RF = 915 MHz

(4)

IIP3

–16

dBm

2.13

System outband input

1 dB compression point

∆f

meas1 = 1 MHz

RF = 315 MHz

(4)

I1dBCP

–31

dBm

RF = 345 MHz

(4)

I1dBCP

–31

dBm

RF = 433.92 MHz

(4)

I1dBCP

–30

dBm

RF = 868.3 MHz

(4)

I1dBCP

–27

dBm

RF = 915 MHz

(4)

I1dBCP

–26

dBm

2.14 LNA input impedance

RF = 315 MHz

in_LNA

(44

– j233)

Ω

RF = 345 MHz

in_LNA

(40

– j211)

Ω

RF = 433.92 MHz

in_LNA

(32

– j169)

Ω

fRF = 868.3 MHz

Zin_LNA

(21

– j78)

Ω

fRF = 915 MHz

Zin_LNA

(18

– j70)

Ω

2.15

Allowable peak RF input

level, ASK and FSK

BER < 10-3, ASK: 100%

(4)

PIN_max

+10

–10

dBm

FSK: fDEV = ±16 kHz

(4)

PIN_max

+10

–10

dBm

2.16

LO spurious emission at

LNA_IN

f < 1 GHz

(4)

–57

dBm

f >1 GHz

(4)

–47

dBm

fRF = 315 MHz

(4)

–100

dBm

fRF = 345 MHz

(4)

–100

dBm

fRF = 433.92 MHz

(4)

–97

dBm

fRF = 868.3 MHz

(4)

–84

dBm

fRF = 915 MHz

(4)

–84

dBm

2.17 Image rejection

Within the complete

image band

(4)

12. Electrical Characteristics: General (Continued)

This device is manufactured with an industrial (not automotive) grade process and process controls. Although this device may

meet certain automotive grade criteria in performance, Atmel can not recommend that this device be used in any automotive

application.

All parameters refer to GND and are valid for Tamb = 25°C, VVS1 = VVS2 = 3.0V (1-battery application), VVS2 = 6.0V (2-battery application)

and VVS2 = VVAUX = 5.0V (Base-station Application). Typical values are given at fRF = 433.92 MHz unless otherwise specified. Details

about current consumption, timing and digital pin properties can be found in the specific sections of the “Electrical Characteristics”.

No. Parameters

Test Conditions

Pin(1)

Symbol

Min.

Typ.

Max.

Unit

Type*

*) Type means: A = 100% tested, B = 100% correlation tested, C = Characterized on samples, D = Design parameter

Note:

1. Pin numbers in brackets mean they were measured with RF_IN matched to 50

Ω according to Figure 3-1 on page 11 with

component values according to Table 3-2 on page 12 and RF_OUT matched to 50

Ω according to Figure 3-10 on page 21

with component values according to Table 3-7 on page 22.

ATA5423-PLSW Scheda tecnica(PDF) 71 Page - ATMEL Corporation

ATA5423-PLSW Scheda tecnica(HTML) 71 Page - ATMEL Corporation

Html Pages

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65 66 67 68 69 70 71 72 73 74 75 76 77 78 79 80 81 82 83 84 85 86 87 88 89 90 91 92 93 94 95 96 97 98 99 100

Scheda tecnica Scarica

Link URL