Motore di ricerca datesheet componenti elettronici
  Italian  ▼
ALLDATASHEETIT.COM

X  

SA9604ASA Scheda tecnica(PDF) 6 Page - Sames

Il numero della parte SA9604ASA
Spiegazioni elettronici  THREE PHASE BIDIRECTIONAL POWER/ENERGY METERING IC WITH SERIAL SPI INTERFACE
PDF  20 Pages
Scroll/Zoom Zoom In 100%  Zoom Out
Produttore elettronici  SAMES [Sames]
Homepage  http://www.sames.co.za
Logo SAMES - Sames

SA9604ASA Scheda tecnica(HTML) 6 Page - Sames

Back Button SA9604ASA Datasheet HTML 2Page - Sames SA9604ASA Datasheet HTML 3Page - Sames SA9604ASA Datasheet HTML 4Page - Sames SA9604ASA Datasheet HTML 5Page - Sames SA9604ASA Datasheet HTML 6Page - Sames SA9604ASA Datasheet HTML 7Page - Sames SA9604ASA Datasheet HTML 8Page - Sames SA9604ASA Datasheet HTML 9Page - Sames SA9604ASA Datasheet HTML 10Page - Sames Next Button
Zoom Inzoom in Zoom Outzoom out
 6 / 20 page
background image
SA9604A
sames
6/20
4.
Power Consumption
The power consumption rating of the SA9604A integrated circuit is less than 50mW.
5.
SPI - INTERFACE
5.1 Description
The serial peripheral interface (SPI) is a synchronous bus for data transfer and is
used when interfacing the SA9604A with any micro-controller. Four pins are used
for the SPI. The four pins are DO (Serial Data Out), DI (Serial Data In), CE (Chip
Enable), and SCK (Serial Clock). The SA9604A is the slave device in an SPI
application, with the micro-controller being the master. The DI and DO pins are the
serial data input and output pins for the SA9604A, respectively. The CE input is used
to initiate and terminate a data transfer. The SCK pin is used to synchronize data
movement between the master (micro-controller) and the slave (SA9604A) devices.
The serial clock (SCK), which is generated by the micro-controller, is active only
during address and data transfer to any device on the SPI bus.
5.2 Register Access
There are four registers for each phase which can be read: active, reactive, voltage
and frequency. Any of these registers may be chosen as the initial register to read.
If the SCK clock input continues after the first register has been read, the contents
of subsequent registers will be output on the DO pin. Transfer will continue until CS
is brough inactive.
To enable registers for reading, the sequence 1 1 0 (6
HEX) must precede the 6 bit
address of the register being accessed.
The various register addresses are shown in the table below:
ID
REGISTER
A5
A4
A3
A2
A1
A0
1
Active:
Phase 1
X
X
0
0
0
0
2
Reactive:
Phase 1
X
X
0
0
0
1
3
Voltage:
Phase 1
X
X
0
0
1
0
4
Frequency:
Phase 1
X
X
0
0
1
1
5
Active:
Phase 2
X
X
0
1
0
0
6
Reactive:
Phase 2
X
X
0
1
0
1
7
Voltage:
Phase 2
X
X
0
1
1
0
8
Frequency:
Phase 2
X
X
0
1
1
1
9
Active:
Phase 3
X
X
1
0
0
0
10
Reactive:
Phase 3
X
X
1
0
0
1
11
Voltage:
Phase 3
X
X
1
0
1
0
12
Frequency:
Phase 3
X
X
1
0
1
1



Html Pages

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20


Scheda tecnica Scarica

Go To PDF Page


Link URL



Lei ha avuto il aiuto da alldatasheet?  [ DONATE ] 

Di alldatasheet   |   Richest di pubblicita   |   contatti   |   Privacy Policy   |   Collegamento alla scheda tecnica    |   scambio Link   |   Ricerca produttore
All Rights Reserved©Alldatasheet.com


Mirror Sites
English : Alldatasheet.com  |   English : Alldatasheet.net  |   Chinese : Alldatasheetcn.com  |   German : Alldatasheetde.com  |   Japanese : Alldatasheet.jp
Russian : Alldatasheetru.com  |   Korean : Alldatasheet.co.kr  |   Spanish : Alldatasheet.es  |   French : Alldatasheet.fr  |   Italian : Alldatasheetit.com
Portuguese : Alldatasheetpt.com  |   Polish : Alldatasheet.pl  |   Vietnamese : Alldatasheet.vn
Indian : Alldatasheet.in  |   Mexican : Alldatasheet.com.mx  |   British : Alldatasheet.co.uk  |   New Zealand : Alldatasheet.co.nz
Family Site : ic2ic.com  |   icmetro.com