CY8C56LP datasheet(21/120 Pages) CYPRESS

21 / 120 page

PRELIMINARY

PSoC® 5LP: CY8C56LP Family

Datasheet

Document Number: 001-84935 Rev. **

Page 21 of 120

Figure 6-1. Clocking Subsystem

6.1.1 Internal Oscillators

6.1.1.1

Internal Main Oscillator

In most designs the IMO is the only clock source required, due

to its ±1% accuracy. The IMO operates with no external

components and outputs a stable clock. A factory trim for each

frequency range is stored in the device. With the factory trim,

tolerance varies from ±1% at 3 MHz, up to ±7% at 62 MHz. The

IMO, in conjunction with the PLL, allows generation of CPU and

system clocks up to the device's maximum frequency (see

Phase-Locked Loop)

The IMO provides clock outputs at 3, 6, 12, 24, 48, and 62 MHz.

6.1.1.2

Clock Doubler

The clock doubler outputs a clock at twice the frequency of the

input clock. The doubler works for input frequency ranges of 6 to

24 MHz (providing 12 to 48 MHz at the output). It can be

configured to use a clock from the IMO, MHzECO, or the DSI

(external pin). The doubler is typically used to clock the USB.

6.1.1.3

Phase-Locked Loop

The PLL allows low frequency, high accuracy clocks to be

multiplied to higher frequencies. This is a tradeoff between

higher clock frequency and accuracy and, higher power

consumption and increased startup time.

The PLL block provides a mechanism for generating clock

frequencies based upon a variety of input sources. The PLL

outputs clock frequencies in the range of 24 to 67 MHz. Its input

and feedback dividers supply 4032 discrete ratios to create

almost any desired system clock frequency. The accuracy of the

PLL output depends on the accuracy of the PLL input source.

The most common PLL use is to multiply the IMO clock at 3 MHz,

where it is most accurate, to generate the CPU and system

clocks up to the device’s maximum frequency.

The PLL achieves phase lock within 250 µs (verified by bit

setting). It can be configured to use a clock from the IMO,

MHzECO or DSI (external pin). The PLL clock source can be

used until lock is complete and signaled with a lock bit. The lock

signal can be routed through the DSI to generate an interrupt.

Disable the PLL before entering low power modes.

6.1.1.4

Internal Low Speed Oscillator

The ILO provides clock frequencies for low power consumption,

including the watchdog timer, and sleep timer. The ILO

generates up to three different clocks: 1 kHz, 33 kHz, and

100 kHz.

The 1 kHz clock (CLK1K) is typically used for a background

‘heartbeat’ timer. This clock inherently lends itself to low power

supervisory operations such as the watchdog timer and long

sleep intervals using the central timewheel (CTW).

The central timewheel is a 1 kHz, free running, 13-bit counter

clocked by the ILO. The central timewheel is always enabled

except in hibernate mode and when the CPU is stopped during

debug on chip mode. It can be used to generate periodic

interrupts for timing purposes or to wake the system from a low

power mode. Firmware can reset the central timewheel.

4-25 MHz

ECO

3-62 MHz

IMO

32 kHz ECO

1,33,100 kHz

ILO

Digital Clock

Divider 16 bit

Digital Clock

Divider 16 bit

Digital Clock

Divider 16 bit

Digital Clock

Divider 16 bit

Digital Clock

Divider 16 bit

Digital Clock

Divider 16 bit

Digital Clock

Divider 16 bit

Digital Clock

Divider 16 bit

Analog Clock

Divider 16 bit

Bus Clock Divider

16 bit

48 MHz

Doubler for

USB

24-67 MHz

PLL

System

Clock Mux

External IO

or DSI

0-66 MHz

Analog Clock

Divider 16 bit

Analog Clock

Divider 16 bit

Analog Clock

Divider 16 bit

Bus

Clock

CPU

Clock

CY8C56LP Scheda tecnica(PDF) 21 Page - Cypress Semiconductor

CY8C56LP Scheda tecnica(HTML) 21 Page - Cypress Semiconductor

Html Pages

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65 66 67 68 69 70 71 72 73 74 75 76 77 78 79 80 81 82 83 84 85 86 87 88 89 90 91 92 93 94 95 96 97 98 99 100 ...More

Scheda tecnica Scarica

Link URL