| Motore di ricerca datesheet componenti elettronici |
|
JS28F512P30TFA Scheda tecnica(PDF) 32 Page - Micron Technology |
|
|
|||||||||||||||||||||||||||||
JS28F512P30TFA Scheda tecnica(HTML) 32 Page - Micron Technology |
|
32 / 86 page ![]() P30-65nm Datasheet Apr 2010 32 Order Number: 208042-05 Note: LK: Lock Setup Command, 60h; LK/D0h: Unlock Command; LK/01h: Lock Command; LK/2Fh: Lock-Down Command. 10.1.5 Block Locking During Suspend Block lock and unlock changes can be performed during an erase suspend. To change block locking during an erase operation, first issue the Erase Suspend command. Monitor the Status Register until SR.7 and SR.6 are set, indicating the device is suspended and ready to accept another command. Next, write the desired lock command sequence to a block, which changes the lock state of that block. After completing block lock or unlock operations, resume the erase operation using the Erase Resume command. Note: A Lock Block Setup command followed by any command other than Lock Block, Unlock Block, or Lock-Down Block produces a command sequence error and set Status Register bits SR.4 and SR.5. If a command sequence error occurs during an erase suspend, SR.4 and SR.5 remains set, even after the erase operation is resumed. Unless the Status Register is cleared using the Clear Status Register command before resuming the erase operation, possible erase errors may be masked by the command sequence error. If a block is locked or locked-down during an erase suspend of the same block, the lock status bits change immediately. However, the erase operation completes when it is resumed. Block lock operations cannot occur during a program suspend. See Appendix A, “Write State Machine” on page 81, which shows valid commands during an erase suspend. Figure 9: Block Locking State Diagram [0 0 0 ] [0 0 1 ] [0 1 1 ] [1 1 1 ] [1 0 1 ] [1 1 0 ] [1 0 0 ] LK / D0 h LK / 01 h LK / 2Fh L K /2 F h LK / D0 h LK / 01 h o r 2 F h LK / D0 h LK / 01 h LK / 2F h LK / 2F h PG M /E R A S E AL L O W E D PG M /ER A SE PR EV EN T ED WP # = V IL = 0 WP # = V IH = 1 Po w e r -U p / Re s e t De f a u lt Po w e r - U p / Re s e t De f a u lt L o ck ed - d o w n L o ck ed -d o w n is d is a b le d b y WP # = V IH V ir t u a l lo c k - do w n A n y L o ck co m m an d s WP # t o g g le W P # to g g le [0 10] |
|
Link URL |
| Lei ha avuto il aiuto da alldatasheet? [ DONATE ] |
Di alldatasheet | Richest di pubblicita | contatti | Privacy Policy | Collegamento alla scheda tecnica | scambio Link | Ricerca produttore All Rights Reserved©Alldatasheet.com |
| Russian : Alldatasheetru.com | Korean : Alldatasheet.co.kr | Spanish : Alldatasheet.es | French : Alldatasheet.fr | Italian : Alldatasheetit.com Portuguese : Alldatasheetpt.com | Polish : Alldatasheet.pl | Vietnamese : Alldatasheet.vn Indian : Alldatasheet.in | Mexican : Alldatasheet.com.mx | British : Alldatasheet.co.uk | New Zealand : Alldatasheet.co.nz |
|
Family Site : ic2ic.com |
icmetro.com |