MT90826 datasheet(5/30 Pages) MITEL

5 / 30 page

Advanced Information

CMOS

MT90826

K13

CLK

Master Clock (5V Tolerant Input): Serial clock for

shifting data in/out on the serial streams. This pin accepts

a clock frequency of 8.192MHz or 16.384 MHz. The CPLL

bit in the control register determines the usage of the

clock frequency. See Table 6 for details.

J13

ODE

Output Drive Enable (5V Tolerant Input): This is the

output-enable control pin for the STo0 to STo31 serial

outputs. See Table 2 for details.

67-70

78,79

82,83

91-94

102-105

113-116

126-129

137-140

H13

H12

G13

G12

F13,F12,E13,E12

B13,A13

A12,B12

C11,C10,C9,C8

A7,B7,A6,B6

A5,B5,A4,B4

A2,B2,A1,B1

E2,F2,E1,F1

STi0/FEi0,

STi1/FEi1

STi2/FEi2

STi3/FEi3

STi4-7/FEi4-7

STi8-9/FEi8-9

STi10-11/FEi10-11

STi12-15/FEi12-15

STi16-19/FEi16-19

STi20-23/FEi20-23

STi24-27/FEi24-27

STi28-31/FEi28-31

Serial Input Streams 0 to 31 and Frame Evaluation

Inputs 0 to 31 (5V Tolerant Inputs): Serial data input

streams. These streams may have data rates of 2.048,

4.096, 8.192 or 16.384 Mb/s, depending upon the value

programmed at bits DR0 - DR2 in the control register. In

the frame evaluation mode, they are used as the frame

evaluation inputs.

61-64

72-75

85-88

96-99

107-110

118,119

122,123

131-134

142-145

G11,F11,E11,D11

D13,C13,D12,C12

A11,B11,A10,B10

B9,A9,B8,A8

C7,C6,C5,C4

A3,B3

D3,C3

D2,C2,C1,D1

G1,G2,H1,H2

STo0 - 3

STo4 - 7

STo8 - 11

STo12 - 15

STo16 - 19

STo20, STo21

STo22, STo23

STo24 - 27

STo28 - 31

ST-BUS Output 0 to 31 (Three-state Outputs). Serial

data output streams. These streams may have data rates

of 2.048, 4.096, 8.192, or 16.384 Mb/s, depending upon

the value programmed at bits DR0 - DR2 in the control

148-153

154,155

158

3-7

8,9

G3,J1,H3,J2,J3,K1,

K2,K3

L2,M1,M2,M3,N1,

N2,N3

D0 - 5,

D6,D7

D9 - 13

D14,D15

Data Bus 0 -15 (5V Tolerant I/O): These pins form the

16-bit data bus of the microprocessor port.

DTA

Data Transfer Acknowledgment (Three-state Output):

This output pulses low from tristate to indicate that a

databus transfer is complete. A pull-up resistor is required

to hold a HIGH level when the pin is tristated.

Data Strobe (5V Tolerant Input): This active low input

works in conjunction with CS to enable the read and write

operations.

R/W

Read/Write (5V Tolerant Input): This input controls the

direction of the data bus lines (D0-D15) during a

microprocessor access.

Chip Select (5V Tolerant Input): Active low input used

by a microprocessor to activate the microprocessor port.

16-20

23-31

M6,N6,N7,M7,N8

N9,N10,M8,M9,L7

L8,M10,L9,A10

A0 - A4

A5-A13

Address 0 - 13 (5V Tolerant Input): These lines provide

the A0 - A13 address lines when accessing the internal

registers or memories.

1,2,39,80,81,120,

121,159,160

E3,F3,K8,

L3,L4,L5,L6

No Connect

Pin Description (continued)

Pin # MQFP

Pin # PBGA

Name

Description

MT90826 Scheda tecnica(PDF) 5 Page - Mitel Networks Corporation

MT90826 Scheda tecnica(HTML) 5 Page - Mitel Networks Corporation

Html Pages

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30

Scheda tecnica Scarica

Link URL