LM7321 datasheet(7/39 Pages) TI1

7 / 39 page

LM7321, LM7322

www.ti.com

SNOSAW8E – MAY 2008 – REVISED SEPTEMBER 2015

7.6

±5-V Electrical Characteristics

Unless otherwise specified, all limited ensured for TA = 25°C, V

+ = 5 V, V− = −5V, V

CM = 0 V, VOUT = 0 V, and RL > 1 MΩ to 0

(1)

PARAMETER

TEST CONDITION

MIN(2)

TYP(3)

MAX(2)

UNIT

−5

±0.7

VCM = −4.5 V and VCM =

VOS

Input Offset Voltage

4.5 V

TA = –40°C to +125°C

−6

Input Offset Voltage

TC VOS

VCM = −4.5 V and VCM = 4.5 V

(4)

±2

µV/°C

Temperature Drift

VCM = −4.5 V

(5)

−2.0

−1.2

TA = –40°C to +125°C

−2.5

Input Bias Current

µA

VCM = 4.5 V

(5)

0.45

TA = –40°C to +125°C

1.5

200

VCM = −4.5 V and VCM =

IOS

Input Offset Current

4.5 V

TA = –40°C to +125°C

300

100

−5 V ≤ VCM ≤ 3 V

TA = –40°C to +125°C

Common Mode

CMRR

Rejection Ratio

−5 V ≤ VCM ≤ 5 V

TA = –40°C to +125°C

104

Power Supply Rejection

2.7 V

≤ VS ≤ 30 V,

PSRR

Ratio

VCM = −4.5 V

TA = –40°C to +125°C

−5.3

−5.1

Common-Mode Voltage

CMRR > 50 dB

Range (Min)

TA = –40°C to +125°C

−5

CMVR

5.1

5.3

Common-Mode Voltage

CMRR > 50 dB

Range (Max)

TA = –40°C to +125°C

−4 V ≤ VO ≤ 4 V

RL = 10 kΩ to 0 V

TA = –40°C to +125°C

Open-Loop Voltage

AVOL

Gain

−4 V ≤ VO ≤ 4 V

RL = 2 kΩ to 0 V

TA = –40°C to +125°C

100

250

RL = 10 kΩ to 0 V

VID = 100 mV

TA = –40°C to +125°C

280

Output Voltage Swing

High

160

350

RL = 2 kΩ to 0 V

VID = 100 mV

TA = –40°C to +125°C

450

from

VOUT

either

200

RL = 10 kΩ to 0 V

rail

VID = −100 mV

TA = –40°C to +125°C

250

Output Voltage Swing

Low

200

RL = 2 kΩ to 0 V

VID = −100 mV

TA = –40°C to +125°C

250

Sourcing

VID = 200 mV, VOUT = −5

TA = –40°C to +125°C

V(6)

IOUT

Output Current

Sinking

VID = −200 mV, VOUT = 5

TA = –40°C to +125°C

V(6)

(1)

Electrical Table values apply only for factory testing conditions at the temperature indicated. Factory testing conditions result in very

limited self-heating of the device such that TJ = TA. No ensured specification of parametric performance is indicated in the electrical

tables under conditions of internal self-heating where TJ > TA.

(2)

All limits are ensured by testing or statistical analysis.

(3)

Typical values represent the most likely parametric norm as determined at the time of characterization. Actual typical values may vary

over time and will also depend on the application and configuration. The typical values are not tested and are not ensured on shipped

production material.

(4)

Offset voltage temperature drift determined by dividing the change in VOS at temperature extremes into the total temperature change.

(5)

Positive current corresponds to current flowing into the device.

(6)

Applies to both single-supply and split-supply operation. Continuous short circuit operation at elevated ambient temperature can result in

exceeding the maximum allowed junction temperature of 150°C. Short circuit test is a momentary test. Output short circuit duration is

infinite for VS ≤ 6 V at room temperature and below. For VS > 6 V, allowable short circuit duration is 1.5 ms.

Submit Documentation Feedback

Product Folder Links: LM7321 LM7322

LM7321 Scheda tecnica(PDF) 7 Page - Texas Instruments

LM7321 Scheda tecnica(HTML) 7 Page - Texas Instruments

Html Pages

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39

Scheda tecnica Scarica

Link URL