BTE5000 / PTE5000 / PTU5000 Series

Precision differential pressure transmitters

3/5

E / 11101 / B

www.first-sensor.com

www.sensortechnics.com

LOAD LIMITATION

4...20 mA output versions

operating

0

200

400

10

20

1000

600

800

Ohm

1200

30

Vsupply

V

range

s

n

o

i

t

i

d

n

o

c

t

s

e

Tn

o

i

r

e

t

i

r

C

e

c

n

e

r

e

f

r

e

t

n

I

y

c

n

e

u

q

e

r

f

o

i

d

a

r

,

d

e

t

a

i

d

a

R

)

I

F

R

(

y

t

i

n

u

m

m

i

d

l

e

i

f

c

i

t

e

n

g

a

m

o

r

t

c

e

l

e

:

3

-

4

-

0

0

0

1

6

N

Ez

H

M

0

0

0

1

o

t

0

8

,

m

/

V

0

1

)

z

H

k

1

(

C

M

A

%

0

8

AO

S

F

%

1

<

/

t

n

e

i

s

n

a

r

t

t

s

a

f

l

a

c

i

r

t

c

e

l

E

)

T

F

E

(

y

t

i

n

u

m

m

i

t

s

r

u

b

:

4

-

4

-

0

0

0

1

6

N

EV

k

2

±

BO

S

F

%

1

<

y

t

i

n

u

m

m

i

e

g

r

a

h

c

s

i

d

c

i

t

a

t

s

o

r

t

c

e

l

E

)

D

S

E

(

t

s

e

t

:

2

-

4

-

0

0

0

1

6

N

Ee

g

r

a

h

c

s

i

d

t

c

a

t

n

o

c

,

V

k

4

±

e

g

r

a

h

c

s

i

d

r

i

a

,

V

k

8

±

BO

S

F

%

1

<

s

e

c

n

a

b

r

u

t

s

i

d

d

e

t

c

u

d

n

o

c

o

t

y

t

i

n

u

m

m

I

s

d

l

e

i

f

y

c

n

e

u

q

e

r

f

-

o

i

d

a

r

y

b

d

e

c

u

d

n

i

:

6

-

4

-

0

0

0

1

6

N

Ez

H

M

0

8

o

t

5

1

.

0

)

z

H

k

1

(

C

M

A

%

0

8

,

V

0

1

AO

S

F

%

1

<

Specification notes:

1.

IP 67 protection for BTE(M)5...A / PTx5...A is given with locked connector only.

2.

Proof pressure is the maximum pressure which may be applied without causing damage to the sensing element.

3.

This is the highest pressure which can be applied to any port at any time. At the same time the differential pressure between

the ports H and L must not exceed the maximum proof pressure.

4.

Non-linearity refers to the Best Straight Line fit measured for offset, full scale span and 1/2 full scale span.

5.

Long term stability is the change in output after one year or 1 million pressure cycles.

6.

Thermal effects tested and guaranteed from 0 - 70 °C relative to 25°. All specifications shown are relative to 25°C.

7.

Full scale span is the algebraic difference between the positive full scale output and zero pressure offset.

8.

Higher pressure applied to port H.

9.

Test are in accordance with EN 61000-6-2.

10. CE-labelling is in accordance with 2004/108/EC.

11. The pressure transmitters must not be used as safety accessories according to article 1, 2.1.3 of the directive 97/23/EC.

12. 0...10 V square rooting output signal on special request.