For price, delivery and to place orders: Hittite Microwave Corporation, 2 Elizabeth Drive, Chelmsford, MA 01824

Phone: 978-250-3343

Fax: 978-250-3373

Order On-line at www.hittite.com

Application Support: Phone: 978-250-3343 or apps@hittite.com

2

HMC1060LP3E

v00.1211

QUAD LOW NOISE HIGH PSRR

LINEAR VOLTAGE REGULATOR

Electrical Specifications

t

Parameter

Conditions

Min

typ

Max

Units

output Voltage on All outputs

1.8

5.2

V

default output Voltage Vr1, Vr2, Vr3

Schematic

3.24

3.3

3.36

V

default output Voltage Vr4

4.9

5.0

5.1

V

PtAt Mode disabled

2

%

PtAt Mode enabled

3

%

input Voltage range (default)

5.3

5.6

V

3.35

Max (Vrx) +

0.3 V

5.6

V

100

mA

50

mA

300

mA

total output Current

500

mA

output noise Voltage density

10 Hz

100 Hz

1 kHz

10 kHz

100 kHz

2200

120

7

3

3

nV/√Hz

integrated output noise 100 Hz to 100 kHz

1.5

µVrms

Load regulation, Vr4

0 to 300 mA

0.007

% / mA

Vr1 PSrr

1 kHz

10 kHz

100 KHz

1 MHz

10 MHz

80

80

72

60

52

dB

Ven = Vdd = 5.6 V;

Maximum Load Current

2.1

mA

Power down Current

Ven = Low; Vrx outputs are floating (high

- impedance) in Power-down Mode

1

2

µA

Start-Up transient time

0 to 90% of final voltage;

en connected to Vdd

50

ms

en turn-on delay

0 to 90% of final output voltage

Cref = 4.7 µF; Cload = 10 µF; Vdd = 5.6

Ven transition from 0 to Vdd

30

ms

enable input en High Level

2

Vdd + 0.3

V

enable input en Low Level

0

0.8

V

thermal Protection threshold Junction

temperature

no loads

150

°C

Maximum dissipated Power

All outputs Loaded

1.6

w

[1] when using external resistors to configure the HMC1060LP3e outputs to non-default levels, the temperature coefficient of external resistors

may increase the output voltage tolerance. note that internal resistors have a temperature coefficient of +270 ppm/°C.

[2] Minimum input voltage (Vdd) is defined by maximum desired output voltage. As an example minimum input voltage (Vdd) of 4.3 V is required

to set the HMC1060LP3e outputs as follows Vr1 = Vr2 = Vr3 = 3.3 V, Vr4 = 4 V.

[3] the outputs will withstand short-circuit conditions for a duration of less than 10 seconds.

Information furnished by Analog Devices is believed to be accurate and reliable. However, no

responsibility is assumed by Analog Devices for its use, nor for any infringements of patents or other

rights of third parties that may result from its use. Specifications subject to change without notice. No

license is granted by implication or otherwise under any patent or patent rights of Analog Devices.

Trademarks and registered trademarks are the property of their respective owners.

For price, delivery, and to place orders: Analog Devices, Inc.,

One Technology Way, P.O. Box 9106, Norwood, MA 02062-9106

Phone: 781-329-4700 • Order online at www.analog.com

Application Support: Phone: 1-800-ANALOG-D