SPC56EL54X datasheet(162/165 Pages) STMICROELECTRONICS

162 / 165 page

Revision history

SPC56ELx, SPC564Lx

162/165

DocID15457 Rev 12

01-Aug-2012

(cont.)

Changed min value to ‘-72’ for symbol ‘THD’.

–In Table 27: ADC conversion characteristics, changed ADC specification

parameter ‘THD’ minimum limit from -72 to -65dB.

–In Table 28: Flash memory program and erase electrical specifications,

changes done are as follows:

TDWPROGRAM, changed typical value from ‘39’ to ‘38’.

TPPROGRAM, changed typical value from ‘48’ to ‘45’ and initial max value from

‘100’ to ‘160’.

T16KPPERASE, inserted typical value ‘270’ and factory avg ‘1000’.

T48KPPERASE, inserted typical value ‘625’ and factory avg ‘1500’.

T64KPPERASE, inserted typical value ‘800’ and factory avg ‘1800’.

T128KPPERASE, inserted typical value ‘1500’ and factory avg ‘2600’.

T256KPPERASE, inserted typical value ‘3000’ and factory avg ‘5200’.

Updated table footnote and removed min column in Table 28: Flash memory

program and erase electrical specifications

–In Table 29: Flash memory timing, added symbol TPSRT ,TESRT and added

table footnote for TPSRT ,TESRT .

– Added Table 31: SPC56XL60/54 SWG Specifications

–In Table 31: SPC56XL60/54 SWG Specifications

Added table footnote for Common Mode.

Changed text from “internal device pad resistance” to “internal device routing

resistance”.

– Added Figure 28: Nexus EVTI Input Pulse Width in Section 3.21.4: Nexus

timing

”.

–In Table 32: Pad AC specifications (3.3 V, IPP_HVE = 0), removed the row

of pad “Pull Up/Downc(3.6 V max)”.

–In Figure 44, updated part numbers (changed ‘PPC’ to ‘SPC’ and ‘F0’ to

‘F2’).

–Replaced Figure 42, Figure 43 with the new versions.

–InTable 20,changed the symbol of spec external decoupling capacitor from

SR to Cext.

In Table 6, changed the ESR range in note text to 1 m

 to 100 m from 30 m

to 150 m

.

–In Section 1.5.32: Sine Wave Generator (SWG)” removed the following text:

Frequency range from 1kHz to 50kHz.

Sine wave amplitude from 0.47 V to 2.26 V.

–In Table 22,changed symbol from ‘C’ to ‘T’ , added “operating current” to the

parameter and updated the maximum value for five additional RunIDD

parameters.

–In Table 22, changed “Conditions” from ‘1.2 V supplies’ to ‘1.2 V supplies

during LBIST (full LBIST configuration)’ for all the parameters.

Removed Table “SWG electrical characteristics”.

Table 45. Document revision history

Date

Revision

Changes

SPC56EL54x Scheda tecnica(PDF) 162 Page - STMicroelectronics

SPC56EL54x Scheda tecnica(HTML) 162 Page - STMicroelectronics

Html Pages

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65 66 67 68 69 70 71 72 73 74 75 76 77 78 79 80 81 82 83 84 85 86 87 88 89 90 91 92 93 94 95 96 97 98 99 100 ...More

Scheda tecnica Scarica

Link URL