MSI2021 datasheet(3/11 Pages) MGCHIP

3 / 11 page

June. 2009. Revision 1.3

MagnaChip Semiconductor Ltd.

Absolute Maximum Ratings

Symbol

Parameter

Min

Max

Unit

VDD

DC Supply Voltage on VDD pin

-0.5

5.5

VSAB

Control Input Voltage (SA, SB)

-0.5

VDD+0.3V

VIN/OUT

In/Out Voltage in Analog IO pins

A0, A1, B0, B1

VDD-4.3

VDD+0.3

IIN/OUT

In/Out Current in Analog IO pins

350

IIN/OUT_PEAK

Peak Current in Analog IO pins (1ms Duration @10% Duty Cycle)

500

ESD

HBM on All Pins

Storage Temperature

-65

150

Note 1:

Stresses beyond the above listed maximum ratings may damage the device permanently. Operating above the recommended

conditions for extended time may stress the device and affect device reliability. Also the device may not operate normally above the

recommended operating conditions. These are stress ratings only.

Recommended Operating Conditions

Symbol

Parameter

Min

Max

Unit

VDD

Supply Voltage

1.65

4.3

VSAB

Control Input Voltage (SA, SB)

VDD

VIN/OUT

In/Out Voltage in Analog IO Voltage

VDD-4.3

VDD

Operating Temperature

-40

°C

DC Electrical Characteristics

All listed typical values are tested at TA=25°C unless otherwise specified.

Symbol

Parameter

Test Conditions

VDD(V)

Min

Typ

Max

Unit

VSAB_H

Control Input High Voltage

1.65 ≤ VDD < 2.3V

1.65

0.9

2.3 ≤ VDD < 2.8V

2.6

1.4

2.8 ≤ VDD < 3.7V

3.3

1.5

VDD = 4.3V

4.3

1.7

VSAB_L

Control Input Low Voltage

1.65 ≤ VDD < 2.8V

1.65

0.4

2.8 ≤ VDD < 3.7V

3.3

0.5

VDD=4.3V

4.3

0.6

ISAB

Control Input Leakage Current

VSAB = 0 and VDD

4.3

-1

μA

ICC

Quiescent Supply Current

VDD=4.3V, VSAB=0 or VDD,

IIN/OUT=0A

4.3

1.0

μA

ICCT

Increase in ICC on VDD pin per

Control Voltage

VSAB=2.6V

4.3

10.0

μA

VSAB=1.8V

4.3

ILEAK_OFF

OFF State Leakage Current on

A* & B* (See Figure 1)

0.3 < VIN/OUT ≤ VDD – 0.3

4.3

-2

μA

ILEAK_ON

ON State Leakage Current on

COMA & COMB (See Figure 1)

0.3 < VIN/OUT ≤ VDD – 0.3

4.3

-2

μA

IOFF

Power OFF Leakage Current on

COMA & COMB (See Figure 1)

VIN/OUT = 4.3V

μA

RON

On-Resistance (See Figure 2)

VIN/OUT = VDD-4.3V, 0.7 and VDD,

IIN/OUT = 100mA

1.65

1.0

3.0

0.4

4.3

0.3

ᅀ

RON

On-Resistance Match Between

Channels (Note 1)

VIN/OUT = 0.7V, IIN/OUT = 100mA

1.65

1.0

3.0

0.06

4.3

0.04

RFLAT_ON

RON Flatness (Note 2)

VIN/OUT = VDD-4.3V, and 0.7V,

IIN/OUT = 100mA

1.65

0.6

3.0

0.3

4.3

0.2

Note 1: ᅀ

RON(MAX) = | RON_MAX(A0, A1, B0, or B1)-RON_MIN(A0, A1, B0, or B1) | @ Same TA, input voltage, and Supply voltage.

Note 2:

RFLAT_ON is defined as the difference between the maximum and minimum value of RON measured over specified VIN/OUT range.

MSI2021 Scheda tecnica(PDF) 3 Page - MagnaChip Semiconductor.

MSI2021 Scheda tecnica(HTML) 3 Page - MagnaChip Semiconductor.

Html Pages

1 2 3 4 5 6 7 8 9 10 11

Scheda tecnica Scarica

Link URL