Catalog Symbol: HPS, HPS-EE, HPS-FF, HPS-JJ,

and HPS-RR

Panel Mount

Agency Information: UL Recognized, Guide IZLT2,

File E14853

CSA Certified: Class 6225-01, File 47235

Flammability Rating: UL 94 HB

HPS

For ⁄‹Ω£™∑ ≈ 1fiΩ¡§∑ to 1⁄Ω™∑ and

Series

SC and Class CC Fuses

Form No. HPS Series

Page 1 of 1

Data Sheet: 2113

1.031" + 0.003"

(26.2mm + 0.08mm)

0.187" + 0.002"

(4.75mm + 0.05mm)

Mounting Hole

Flange Rear of Panel

+

+

0.890"

0.003"

(22.6mm

0.08mm)

1.312" + 0.003"

(33.3mm + 0.08mm)

1.312" + 0.003"

(33.3mm + 0.08mm)

0.88"

(22.2mm)

2.81" Max.

(71.4mm)

With Fuse

Without Fuse

2.41" Max.

(64.3mm)

0.80"

(20.2mm)

1.78"

(45.2mm)

0.180"

(4.6mm)

1.125"

(28.6mm)

F

SE

.250"

± .003"

(6.35

± .08mm)

(Typ. 2)

Mounting Hole

Flange Front of Panel

The only controlled copy of this Data Sheet is the electronic read-only version located on the Bussmann Network Drive. All other copies of this document are by definition uncontrolled. This bulletin is

intended to clearly present comprehensive product data and provide technical information that will help the end user with design applications. Bussmann reserves the right, without notice, to change

design or construction of any products and to discontinue or limit distribution of any products. Bussmann also reserves the right to change or update, without notice, any technical information con-

tained in this bulletin. Once a product has been selected, it should be tested by the user in all possible applications.

Dimensional Data

General Information:

• Bayonet-type knob.

• Combination ⁄Ω¢∑ quick-connect/solder terminals. (Standard

solder type terminals available.)

• The -EE, -JJ, -FF, and -RR holders are UL Recognized for

applications requiring branch circuit protection.

• Do not put tension on line (rear) terminal.

Electrical Ratings

Catalog

Volts

Symbol

Amps

AC

Fuse Description

HPS

30(3) (4)

600

⁄‹Ω£™∑x 1⁄Ω™∑

HPS-L

5

600

BBS,⁄‹Ω£™∑ ≈ 1‹Ω•∑ fuses.

HPS-EE

15

600

SC 0-15, ⁄‹Ω£™∑ ≈ 1fiΩ¡§∑ fuses.

HPS-JJ

20

600

SC 20, ⁄‹Ω£™∑ ≈ 1⁄‹Ω£™∑ fuses.

HPS-F-EE(2)

15

600

Sleeve on body, leaded for ⁄‹Ω£™∑≈1fiΩ¡§∑

fuses.

HPS-FF(2)

30(3)

480

SC 25 & 30, ⁄‹Ω£™∑ ≈ 1fiΩ•∑ fuses.

HPS-RR(2)

30(3)

600

KTK-R, LP-CC, FNQ-R Class CC fuses.

HPS-W(1) (2) 30(3)

600

⁄‹Ω£™∑ ≈ 1fiΩ•∑ fuses.

(1)No UL Recognition

(2)No CSA Certification

(3)20A max when used with quick connect terminals.

(4)HPS rated at 25A for CSA.

CE logo denotes compliance with European Union Low Voltage Directive

(50-1000Vac, 75-1500Vdc). Refer to Data Sheet: 8002 or contact

Bussmann Application Engineering at 636-527-1270 for more information.

Maximum panel thickness, mounting flange in front of panel

Assumes Pollution Degree 3 per UL 840:

Conductive pollution, or dry, nonconductive pollution that

becomes conductive due to condensation that is expected.

Maximum panel thickness

not including any sealing gaskets.

System Voltage

600V

480

277

240

120

Fuseholder

mm Inches mm Inches mm Inches mm Inches mm Inches

HPS

1.50 1/32” 2.39 3/32” 6.66 1/4”

7.21 9/32” 8.69

5/8”

Thicker panels may be used if fuse holder load terminal is fully insulated, using a

UL recognized (VW-1) insulative heat-shrink tubing, or if anticipated environment

is of Pollution Degree 1 or 2, or if panel is nonconductive.

Pollution Degree 2- Normally, only nonconductive pollution. However, a temporary

conductivity caused by condensation may be expected.

Pollution Degree 1- No pollution or only dry, nonconductive pollution.

The pollution has no influence.

Maximum panel thickness, mounting flange behind the panel:

5.08mm/0.200” (flush to knob collar)

6-3-04

SB04184