AD9201ARS datasheet(11/21 Pages) AD

11 / 21 page

AD9201

–10–

REV. D

REFERENCE AND REFERENCE BUFFER

The reference and buffer circuitry on the AD9201 is configured

for maximum convenience and flexibility. An illustration of the

equivalent reference circuit is show in Figure 26. The user can

select from five different reference modes through appropriate

pin-strapping (see Table I below). These pin strapping options

cause the internal circuitry to reconfigure itself for the appropri-

ate operating mode.

Table I. Table of Modes

Mode

Input Span

REFSENSE Pin Figure

1 V

VREF

2 V

AGND

Programmable

1 + (R1/R2)

See Figure

External

= External Ref

AVDD

1 V Mode (Figure 22)—provides a 1 V reference and 1 V input

full scale. Recommended for applications wishing to optimize

high frequency performance, or any circuit on a supply voltage

of less than 4 V. The part is placed in this mode by shorting the

REFSENSE pin to the VREF pin.

I OR QREFT

I OR QREFB

IINA

IINB

VREF

0.1 F10 F

0.1 F

AD9201

0.1 F

10 F

QINB

QINA

REFSENSE

Figure 22. 0 V to 1 V Input

2 V Mode (Figure 23)—provides a 2 V reference and 2 V input

full scale. Recommended for noise sensitive applications on 5 V

supplies. The part is placed in 2 V reference mode by grounding

(shorting to AVSS) the REFSENSE pin.

I OR QREFT

I OR QREFB

IINA

IINB

VREF

0.1 F10 F

0.1 F

AD9201

0.1 F

10 F

QINB

QINA

REFSENSE

Figure 23. 0 V to 2 V Input

Externally Set Voltage Mode (Figure 24)—this mode uses

the on-chip reference, but scales the exact reference level though

the use of an external resistor divider network. VREF is wired to

the top of the network, with the REFSENSE wired to the tap

point in the resistor divider. The reference level (and input full

scale) will be equal to 1 V

× (R1 + R2)/R1. This method can be

used for voltage levels from 0.7 V to 2.5 V.

I OR QREFT

I OR QREFB

VREF

0.1 F10 F

0.1 F

AD9201

REFSENSE

+ –

AVSS

0.1 F

1 F

VREF = 1 + R2

Figure 24. Programmable Reference

External Reference Mode (Figure 25)—in this mode, the on-

chip reference is disabled, and an external reference is applied to

the VREF pin. This mode is achieved by tying the REFSENSE

pin to AVDD.

EXT

REFERENCE

AVDD

I OR QREFT

I OR QREFB

IINA

IINB

VREF

0.1 F10 F

0.1 F

AD9201

0.1 F

10 F

QINB

QINA

REFSENSE

Figure 25. External Reference

Reference Buffer—The reference buffer structure takes the

voltage on the VREF pin and level-shifts and buffers it for use

by various subblocks within the two A/D converters. The two

converters share the same reference buffer amplifier to maintain

the best possible gain match between the two converters. In the

interests of minimizing high frequency crosstalk, the buffered

references for the two converters are separately decoupled on

the IREFB, IREFT, QREFB and QREFT pins, as illustrated in

Figure 26.

AD9201ARS Scheda tecnica(PDF) 11 Page - Analog Devices

AD9201ARS Scheda tecnica(HTML) 11 Page - Analog Devices

Html Pages

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21

Scheda tecnica Scarica

Link URL