AC08FSM datasheet(88/223 Pages) TECCOR

88 / 223 page

http://www.teccor.com

E9 - 2

+1 972-580-7777

Thyristor Product Catalog

Sidac

Data Sheets

Specific Test Conditions

di/dt — Critical rate-of-rise of on-state current

dv/dt — Critical rate-of-rise of off-state voltage at rated VDRM;

TJ ≤ 100 °C

IBO — Breakover current 50/60 Hz sine wave

IDRM — Repetitive peak off-state current 50/60 Hz sine wave; V = VDRM

IH — Dynamic holding current 50/60 Hz sine wave; R = 100 Ω

IT(RMS) — On-state RMS current TJ ≤ 125 °C 50/60 Hz sine wave

ITSM — Peak one-cycle surge current 50/60 Hz sine wave (non-

repetitive)

RS — Switching resistance

50/60 Hz sine wave

VBO — Breakover voltage 50/60 Hz sine wave

VDRM — Repetitive peak off-state voltage

VTM — Peak on-state voltage; IT = 1 A

General Notes

•

All measurements are made at 60 Hz with a resistive load at an

ambient temperature of +25 °C unless otherwise specified.

•

Storage temperature range (TS) is -65 °C to +150 °C.

•The case (TC) or lead (TL) temperature is measured as shown on

the dimensional outline drawings in the “Package Dimensions” sec-

tion of this catalog.

•

Junction temperature range (TJ) is -40 °C to +125 °C.

•

Lead solder temperature is a maximum of +230 °C for 10-second

maximum;

≥1/16" (1.59 mm) from case.

Electrical Specification Notes

(1) See Figure E9.5 for VBO change versus junction temperature.

(2) See Figure E9.6 for IBO versus junction temperature.

(3) See Figure E9.2 for IH versus case temperature.

(4) See Figure E9.13 for test circuit.

(5) See Figure E9.1 for more than one full cycle rating.

(6) TC ≤ 90 °C for TO-92 Sidac

TC ≤ 105 °C for TO-202 Sidacs

TL ≤ 100 °C for DO-15X

TL ≤ 90 °C for DO-214

(7) See Figure E9.14 for clarification of sidac operation.

(8) For best sidac operation, the load impedance should be near or

less than switching resistance.

(9) See package outlines for lead form configurations. When ordering

special lead forming, add type number as suffix to part number.

(10) Do not use electrically connected mounting tab or center lead.

V-I Characteristics

Type

Part No.

IT(RMS)

VDRM

VBO

IDRM

IBO

TO-92

DO-15X

(10)

TO-202

DO-214

(7) (8)

Amps

Volts

(1)

Volts

µAmps

(2)

µAmps

(3) (4)

mAmps

See “Package Dimensions” section for variations. (9)

MAX

MIN

MAX

TYP

MAX

K0900E70

K0900G

K0900S

±70

150

K1050E70

K1050G

K1050S

±90

113

150

K1100E70

K1100G

K1100S

±90

104

118

150

K1200E70

K1200G

K1200S

±90

110

125

150

K1300E70

K1300G

K1300S

±90

120

138

150

K1400E70

K1400G

K1400S

±90

130

146

150

K1500E70

K1500G

K1500S

±90

140

170

150

K2000E70

K2000G

K2000F1

K2000S

±180

190

215

150

K2200E70

K2200G

K2200F1

K2200S

±180

205

230

150

K2400E70

K2400G

K2400F1

K2400S

±190

220

250

150

K2500E70

K2500G

K2500F1

K2500S

±200

240

280

150

K3000F1

±200

270

330

150

VBO VS

–

()

IS IBO

–

()

--------------------------------

-V

VDRM

IDRM

IBO

VBO

(IS - IBO)

(VBO - VS)

RS =

-I

AC08FSM Scheda tecnica(PDF) 88 Page - Teccor Electronics

AC08FSM Scheda tecnica(HTML) 88 Page - Teccor Electronics

Html Pages

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65 66 67 68 69 70 71 72 73 74 75 76 77 78 79 80 81 82 83 84 85 86 87 88 89 90 91 92 93 94 95 96 97 98 99 100 ...More

Scheda tecnica Scarica

Link URL