GD25LB128DSJS datasheet(30/75 Pages) GIGADEVICE

30 / 75 page

1.8V Uniform Sector

Dual and Quad Serial Flash

GD25LB128D

Quad I/O Word Fast Read with

“8/16/32/64-Byte Wrap Around” in Standard SPI mode

The Quad I/O Word Fast Read command can be used to access a specific portion within a page by issuing

“Set Burst

with Wrap

” (77H) commands prior to E7H. The “Set Burst with Wrap” (77H) command can either enable or disable the “Wrap

Around

” feature for the following E7H commands. When “Wrap Around” is enabled, the data being accessed can be limited

to either an 8/16/32/64-byte section of a 256-byte page. The output data starts at the initial address specified in the command,

once it reaches the ending boundary of the 8/16/32/64-byte section, the output will wrap around the beginning boundary

automatically until CS# is pulled high to terminate the command.

The Burst with Wrap feature allows applications that use cache to quickly fetch a critical address and then fill the cache

afterwards within a fixed length (8/16/32/64-byte) of data without issuing multiple read commands. The

“Set Burst with Wrap”

command allows three

“Wrap Bits” W6-W4 to be set. The W4 bit is used to enable or disable the “Wrap Around” operation

while W6-W5 is used to specify the length of the wrap around section within a page.

7.13.

Set Burst with Wrap (77H)

The Set Burst with Wrap command is used in conjunction with

“Quad I/O Fast Read” and “Quad I/O Word Fast Read”

command to access a fixed length of 8/16/32/64-byte section within a 256-byte page.

The Set Burst with Wrap command sequence: CS# goes low  Send Set Burst with Wrap command  Send 24

dummy bits  Send 8 bits

“Wrap bits”  CS# goes high.

W6,W5

W4=0

W4=1 (default)

Wrap Around

Wrap Length

Wrap Around

Wrap Length

0, 0

Yes

8-byte

N/A

0, 1

Yes

16-byte

N/A

1, 0

Yes

32-byte

N/A

1, 1

Yes

64-byte

N/A

If the W6-W4 bits are set by the Set Burst with Wrap command, all the following

“Quad I/O Fast Read” and “Quad I/O

Word Fast Read

” command will use the W6-W4 setting to access the 8/16/32/64-byte section within any page. To exit the

“Wrap Around” function and return to normal read operation, another Set Burst with Wrap command should be issued to set

W4=1. In QPI mode, the

“Burst Read with Wrap (0CH)” command should be used to perform the Read Operation with “Wrap

Around

” feature. The Wrap Length set by W5-W6 in Standard SPI mode is still valid in QPI mode and can also be re-

configured by

“Set Read Parameters (C0H) command.

Figure14. Set Burst with Wrap Sequence Diagram

Command

77H

CS#

SCLK

IO0

IO1

9 10 11 12 13 14 15

W6-W4

IO2

IO3

GD25LB128DSJS Scheda tecnica(PDF) 30 Page - GigaDevice Semiconductor (Beijing) Inc.

GD25LB128DSJS Scheda tecnica(HTML) 30 Page - GigaDevice Semiconductor (Beijing) Inc.

Html Pages

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65 66 67 68 69 70 71 72 73 74 75

Scheda tecnica Scarica

Link URL