ADP1190AACBZ-R7 datasheet(3/12 Pages) AD

3 / 12 page

Data Sheet

ADP1190A

SPECIFICATIONS

VIN = 1.8 V, VEN = VIN, ILOAD = 200 mA, CIN = COUT = 1 µF, TA = 25°C, unless otherwise noted.

Table 1.

Parameter

Symbol

Test Conditions/Comments

Min

Typ

Max

Unit

INPUT VOLTAGE RANGE

VIN

TJ = −40°C to +85°C

1.4

3.6

EN INPUT

EN Input Threshold

VEN_TH

1.4 V < VIN < 1.8 V, TJ = −40°C to +85°C (active low)

0.35

1.2

1.8 V ≤ VIN ≤ 3.6 V, TJ = −40°C to +85°C (active low)

0.45

1.2

Logic High Voltage

VIH

1.4 V ≤ VIN ≤ 3.6 V

1.2

Logic Low Voltage

VIL

1.4 V ≤ VIN ≤ 3.6 V (chip enable)

0.35

CURRENT

Shutdown Current

IOFF

EN = VIN or open

0.7

µA

EN = VIN or open, TJ = −40°C to +85°C

µA

Analog Switch Off Current

IA_OFF

Into S1, EN = VIN

0.2

µA

LOAD SWITCH, VIN TO VOUT RESISTANCE

RDSON_L

VIN = 3.6 V, ILOAD = 200 mA, EN = GND

mΩ

VIN = 2.5 V, ILOAD = 200 mA, EN = GND

mΩ

VIN = 1.8 V, ILOAD = 200 mA, EN = GND, TJ = −40°C to +85°C

100

200

mΩ

SIGNAL SWITCH RESISTANCE

RDSON_S

Maximum value of analog input sweep

VIN = 3.6 V, ILOAD = 10 mA, EN = GND

VIN = 2.5 V, ILOAD = 10 mA, EN = GND

VIN = 1.8 V, ILOAD = 10 mA, EN = GND

RDS Flatness

VIN = 3.6 V, ILOAD = 10 mA, EN = GND

0.2

VIN = 1.8 V, ILOAD = 10 mA, EN = GND

0.2

SIGNAL SWITCH INPUT CAPACITANCE

CIN

OUTPUT DISCHARGE RESISTANCE

RDIS

At the output side of the load switch and each analog

signal switch output, T1, T2, T3, and T4

215

−3 dB BANDWIDTH

BW−3 dB

VIN = 3.3 V, RLOAD = 50 Ω, CLOAD = 5 pF

MHz

VOUT TIME

Turn-On Delay Time

tON_DLY

ILOAD = 200 mA, EN = GND, CLOAD = 0. 1 µF

Turn-Off Delay Time

tOFF_DLY

VIN = 3.6 V, ILOAD = 200 mA, EN = 1.5 V, CLOAD = 0.1 µF

µs

Timing Diagram

Figure 2. Timing Diagram

90%

10%

VOUT

tON_DLY

tOFF_DLY

Rev. 0 | Page 3 of 12

ADP1190AACBZ-R7 Scheda tecnica(PDF) 3 Page - Analog Devices

ADP1190AACBZ-R7 Scheda tecnica(HTML) 3 Page - Analog Devices

Html Pages

1 2 3 4 5 6 7 8 9 10 11 12

Scheda tecnica Scarica

Link URL