L033MU01RI datasheet(27/61 Pages) SPANSION

27 / 61 page

September 12, 2006

Am29LV033MU

DA TA

SH EET

sequence. Note that the SecSi Sector, autoselect, and

CFI functions are unavailable when a program opera-

tion is in progress.

When the Embedded Program algorithm is complete,

the device then returns to the read mode and ad-

dresses are no longer latched. The system can deter-

mine the status of the program operation by using

DQ7, DQ6, or RY/BY#. Refer to the Write Operation

Status section for information on these status bits.

Any commands written to the device during the Em-

bedded Program Algorithm are ignored. Note that a

hardware reset immediately terminates the program

operation. The program command sequence should

be reinitiated once the device has returned to the read

mode, to ensure data integrity.

Programming is allowed in any sequence and across

sector boundaries. A bit cannot be programmed

from “0” back to a “1.” Attempting to do so may

cause the device to set DQ5 = 1, or cause the DQ7

and DQ6 status bits to indicate the operation was suc-

cessful. However, a succeeding read will show that the

data is still “0.” Only erase operations can convert a “0”

to a “1.”

Note: Single byte programming is not supported in x8-mode.

Write buffer programming must be used during x8-mode

operation.

Unlock Bypass Command Sequence

The unlock bypass feature allows the system to pro-

gram bytes to the device faster than using the stan-

dard program command sequence. The unlock bypass

command sequence is initiated by first writing two un-

lock cycles. This is followed by a third write cycle con-

taining the unlock bypass command, 20h. The device

then enters the unlock bypass mode. A two-cycle un-

lock bypass program command sequence is all that is

required to program in this mode. The first cycle in this

sequence contains the unlock bypass program com-

mand, A0h; the second cycle contains the program

address and data. Additional data is programmed in

the same manner. This mode dispenses with the initial

two unlock cycles required in the standard program

command sequence, resulting in faster total program-

ming time. Table 10 shows the requirements for the

command sequence.

During the unlock bypass mode, only the Unlock By-

pass Program and Unlock Bypass Reset commands

are valid. To exit the unlock bypass mode, the system

must issue the two-cycle unlock bypass reset com-

mand sequence. The first cycle must contain the data

90h. The second cycle must contain the data 00h. The

device then returns to the read mode.

Write Buffer Programming

Write buffer programming allows the system to write a

maximum of 32 bytes in one programming operation.

The effective programming time is faster than the stan-

dard programming algorithms. The write buffer pro-

gramming command sequence is initiated by first

writing two unlock cycles. This is followed by a third

write cycle containing the Write Buffer Load command

written at the Sector Address in which programming

will occur. The fourth cycle writes the sector address

and the number of byte locations, minus one, to be

programmed. For example, if the system will program

6 unique address locations, then 05h should be written

to the device. This tells the device how many write

buffer addresses will be loaded with data and therefore

when to expect the Program Buffer to Flash command.

The number of locations to program cannot exceed

the size of the write buffer or the operation will abort.

The fifth cycle writes the first address location and

data to be programmed. A write-buffer-page is se-

lected by address bits AMAX–A5. All subsequent ad-

dress/data

pairs

m u st

f a ll

within

the

selected-write-buffer-page. The system then writes the

remaining address/data pairs into the write buffer.

Write buffer locations may be loaded in any order.

The write-buffer-page address must be the same for

all address/data pairs loaded into the write buffer. That

is, write buffer programming cannot occur across mul-

tiple write-buffer pages or sectors. If the system at-

tempts to load programming data outside of the

selected write-buffer page, the operation will abort.

Note that if a Write Buffer address location is loaded

multiple times, the address/data pair counter will be

decremented for every data load operation. The host

s ystem mu st therefore account fo r l oading a

write-buffer location more than once. The counter dec-

rements for each data load operation, not for each

unique write-buffer-address location. Additionally, the

last data loaded prior to the Program Buffer to Flash

command will be programmed into the device. Note

also that if an address location is loaded more than

once into the buffer, the final data loaded for that ad-

dress will be programmed.

Once the specified number of write buffer locations

have been loaded, the system must then write the Pro-

gram Buffer to Flash command at the sector address.

Any other address and data combination aborts the

Write Buffer Programming operation. The device then

begins programming. Data polling should be used

while monitoring the last address location loaded into

the write buffer. DQ7, DQ6, DQ5, and DQ1 should be

monitored to determine the device status during Write

Buffer Programming.

The write-buffer programming operation can be sus-

pended using the standard program suspend/resume

L033MU01RI Scheda tecnica(PDF) 27 Page - SPANSION

L033MU01RI Scheda tecnica(HTML) 27 Page - SPANSION

Html Pages

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61

Scheda tecnica Scarica

Link URL