A1696PKHTN-RDLPTYCD datasheet(12/14 Pages) ALLEGRO

12 / 14 page

Position Sensor IC with Speed and Direction Output

A1696PKH

Allegro MicroSystems

955 Perimeter Road

Manchester, NH 03103-3353 U.S.A.

www.allegromicro.com

POWER DERATING

The device must be operated below the maximum junction

temperature of the device, TJ(max). Under certain combinations of

peak conditions, reliable operation may require derating supplied

power or improving the heat dissipation properties of the appli-

cation. This section presents a procedure for correlating factors

affecting operating TJ. (Thermal data is also available on the

Allegro MicroSystems website.)

The Package Thermal Resistance, RθJA, is a figure of merit sum-

marizing the ability of the application and the device to dissipate

heat from the junction (die), through all paths to the ambient air.

Its primary component is the Effective Thermal Conductivity,

K, of the printed circuit board, including adjacent devices and

traces. Radiation from the die through the device case, RθJC, is

a relatively small component of RθJA. Ambient air temperature,

TA, and air motion are significant external factors, damped by

overmolding.

The effect of varying power levels (Power Dissipation, PD), can

be estimated. The following formulas represent the fundamental

relationships used to estimate TJ, at PD.

PD = VIN

× IIN

(1)

T = PD

× RθJA

(2)

TJ = TA + ΔT

(3)

For example, given common conditions such as: TA= 25°C, VCC

= 12 V, ICC = 7 mA, and RθJA = 165°C/W, then:

PD = VCC

× ICC = 12 V × 7 mA = 84 mW

T = PD

× RθJA = 84 mW × 165°C/W = 13.9°C

TJ = TA + ΔT = 25°C + 13.9°C = 38.9°C

A worst-case estimate, PD(max), represents the maximum allow-

able power level (VCC(max), ICC(max)), without exceeding TJ(max),

at a selected RθJA and TA.

Example:

Reliability for VCC at TA=150°C, estimated values based on pac-

kage KH, using single layer PCB.

Observe the worst-case ratings for the device, specifically:

RθJA=165°C/W, TJ(max) =165°C, VCC(absmax)= 24 V, and ICC =

12 mA.

Calculate the maximum allowable power level, PD(max). First,

invert equation 3:

T(max) = TJ(max) – TA = 165°C–150°C = 15°C

This provides the allowable increase to TJ resulting from internal

power dissipation. Then, invert equation 2:

PD(max) = ΔT(max) ÷RθJA =15°C÷165°C/W=91mW

Finally, invert equation 1 with respect to voltage:

VCC(est) = PD(max) ÷ ICC= 91 mW÷12mA=7.6 V

The result indicates that, at TA, the application and device can

dissipate adequate amounts of heat at voltages ≤VCC(est).

Compare VCC(est) to VCC(max). If VCC(est) ≤ VCC(max), then reli-

able operation between VCC(est) and VCC(max) requires enhanced

RθJA. If VCC(est) ≥ VCC(max), then operation between VCC(est) and

VCC(max) is reliable under these conditions.

THERMAL CHARACTERISTICS: May require derating at maximum conditions

Characteristic

Symbol

Test Conditions*

Value

Unit

Package Thermal Resistance

RθJA

1-layer PCB with copper limited to solder pads

165

°C/W

*Additional thermal information available on the Allegro website.

A1696PKHTN-RDLPTYCD Scheda tecnica(PDF) 12 Page - Allegro MicroSystems

A1696PKHTN-RDLPTYCD Scheda tecnica(HTML) 12 Page - Allegro MicroSystems

Html Pages

1 2 3 4 5 6 7 8 9 10 11 12 13 14

Scheda tecnica Scarica

Link URL