R7FA2L1AB2DFM datasheet(21/114 Pages) RENESAS

21 / 114 page

Table 2.1

Absolute maximum ratings (2 of 2)

Parameter

Symbol

Value

Unit

Operating temperature*2 *3 *4

Topr

-40 to +85

-40 to +105

°C

Storage temperature

Tstg

-55 to +125

°C

Note 1. Ports P205, P206, P400, P401, and P407 are 5V-tolerant.

Do not input signals or an I/O pull-up power supply while the device is not powered. The current injection that results from input of

such a signal or I/O pull-up might cause malfunction and the abnormal current that passes in the device at this time might cause

degradation of internal elements.

Note 2. See section 2.2.1. Tj/Ta Definition.

Note 3. Contact Renesas Electronics sales office for information on derating operation under Ta = +85°C to +105°C.

Derating is the systematic reduction of load for improved reliability.

Note 4. The upper limit of the operating temperature is 85°C or 105°C, depending on the product.

Caution: Permanent damage to the MCU may result if absolute maximum ratings are exceeded.

To preclude any malfunctions due to noise interference, insert capacitors with high frequency

characteristics between the VCC and VSS pins, between the AVCC0 and AVSS0 pins, and between the

VREFH0 and VREFL0 pins when VREFH0 is selected as the high potential reference voltage for the

ADC12. Place capacitors of the following value as close as possible to every power supply pin and use

the shortest and heaviest possible traces:

● VCC and VSS: about 0.1 µF

● AVCC0 and AVSS0: about 0.1 µF

● VREFH0 and VREFL0: about 0.1 µF

Also, connect capacitors as stabilization capacitance.

Connect the VCL pin to a VSS pin by a 4.7 µF capacitor. Connect the VCC_DCDC pin to a VSS_DCDC pin

by a 1.0 µF capacitor. Each capacitor must be placed close to the pin.

Table 2.2

Recommended operating conditions

Parameter

Symbol

Min

Typ

Max

Unit

Power supply voltages

VCC*1 *2

1.6

—

5.5

VSS

—

Switching regulator power supply voltage

VCC_DCDC

VCC_DCDC = VCC

2.4

—

5.5

Analog power supply voltages

AVCC0*1 *2

1.6

—

5.5

AVSS0

—

VREFH0

When used as ADC12

Reference

1.6

—

AVCC0 V

VREFL0

—

Note 1. Use AVCC0 and VCC under the following conditions:

AVCC0 = VCC

Note 2. When powering on the VCC and AVCC0 pins, power them on at the same time or the VCC pin first and then the AVCC0 pins.

When powering off the VCC and AVCC0 pins, power them off at the same time or the AVCC0 pin first and then the VCC pins.

Table 2.3

Recommended operating conditions

Conditions: VCC = AVCC0 = 1.8 to 5.5 V

Parameter

Symbol

Value

External capacitance for stabilizing

connected to TSCAP pin

CTSCAP

10 nF ± 10%*1

Note 1. Use a multilayer ceramic capacitor with a nominal capacitance of 10 nF and a capacitance tolerance of ± 10% or less. Select a

capacitor with a temperature characteristic of ± 15% or less, such as X7R (EIA), to match the operating environment.

2.2

DC Characteristics

RA2L1 Datasheet

2. Electrical Characteristics

R01DS0385EJ0160 Rev.1.60

Oct 14, 2025

Page 21 of 114

R7FA2L1AB2DFM Scheda tecnica(PDF) 21 Page - Renesas Technology Corp

R7FA2L1AB2DFM Scheda tecnica(HTML) 21 Page - Renesas Technology Corp

Html Pages

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65 66 67 68 69 70 71 72 73 74 75 76 77 78 79 80 81 82 83 84 85 86 87 88 89 90 91 92 93 94 95 96 97 98 99 100 ...More

Scheda tecnica Scarica

Link URL