M38K02FDFP datasheet(90/328 Pages) RENESAS

90 / 328 page

FUNCTIONAL DESCRIPTION

Rev.2.00

Oct 05, 2006

page 73 of 112

38K0 Group

REJ09B0337-0200

HARDWARE

Comparator and Control Circuit

The comparator and control circuit compares an analog input volt-

age with the comparison voltage, and then stores the result in the

AD conversion registers 1, 2. When an A/D conversion is com-

pleted, the control circuit sets the AD conversion completion bit

and the AD interrupt request bit to “1”.

Note that because the comparator consists of a capacitor cou-

pling, set f(system clock) to 500 kHz or more during an A/D

conversion.

Fig. 102 Structure of AD control register

Fig. 103 10-bit A/D mode reading

AD control register

(ADCON : address 003616)

AD conversion completion bit

0 : Conversion in progress

1 : Conversion completed

Analog input pin selection bits

0 0 0 : P10/DQ0/AN0

0 0 1 : P11/DQ1/AN1

0 1 0 : P12/DQ2/AN2

0 1 1 : P13/DQ3/AN3

1 0 0 : P14/DQ4/AN4

1 0 1 : P15/DQ5/AN5

1 1 0 : P16/DQ6/AN6

1 1 1 : P17/DQ7/AN7

Not used (indefinite at read)

(These bits are write disabled bits.)

10-bit reading

(Read address 003816 before 003716)

Note : Bits 2 to 7 of address 003816 become “0”

at reading.

b7 b6 b5 b4 b3 b2 b1 b0

b9 b8 b7 b6 b5 b4 b3 b2

(address 003816)

(address 003716)

8-bit reading

(Read only address 003716)

(address 003716)

A/D CONVERTER

The functional blocks of the A/D converter are described below.

[AD Conversion Register 1, 2 (AD1, AD2)]

003716, 003816

The AD conversion register is a read-only register that stores the

result of an A/D conversion. When reading this register during an

A/D conversion, the previous conversion result is read.

Bit 7 of the AD conversion register 2 must be set to “0”.Not only

10-bit reading but also only high-order 8-bit reading of conversion

result can be performed by selecting the reading procedure of the

AD conversion registers 1, 2 after A/D conversion is completed (in

Figure 103).

The 8-bit reading inclined to MSB is performed when reading the

AD converter register 1 after A/D conversion is started or reset;

and when the AD converter register 1 is read after reading the AD

converter register 2, the 8-bit reading inclined to LSB is per-

formed.

[AD Control Register (ADCON)] 003616

The AD control register controls the A/D conversion process. Bits

0 to 2 select a specific analog input pin. Bit 3 signals the comple-

tion of an A/D conversion. The value of this bit remains at “0”

during an A/D conversion, and changes to “1” when an A/D con-

version ends. Writing “0” to this bit starts the A/D conversion.

Comparison Voltage Generator

The comparison voltage generator divides the voltage between

VREF and AVSS into 1024, and that outputs the comparison volt-

age.

The A/D converter successively compares the comparison voltage

Vref in each mode, dividing the VREF voltage (see below), with the

input voltage.

• 10-bit reading

Vref =

✕ n (n = 0–1023)

• 8-bit reading

Vref =

✕ n (n = 0–255)

Channel Selector

The channel selector selects one of the input ports P17/AN7–P10/

AN0.

VREF

256

VREF

1024

M38K02FDFP Scheda tecnica(PDF) 90 Page - Renesas Technology Corp

M38K02FDFP Scheda tecnica(HTML) 90 Page - Renesas Technology Corp

Html Pages

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65 66 67 68 69 70 71 72 73 74 75 76 77 78 79 80 81 82 83 84 85 86 87 88 89 90 91 92 93 94 95 96 97 98 99 100 ...More

Scheda tecnica Scarica

Link URL