M38K02FDFP datasheet(92/328 Pages) RENESAS

92 / 328 page

FUNCTIONAL DESCRIPTION

Rev.2.00

Oct 05, 2006

page 75 of 112

38K0 Group

REJ09B0337-0200

HARDWARE

Fig. 106 Structure of Watchdog timer control register

Fig. 105 Block diagram of Watchdog timer

WATCHDOG TIMER

The watchdog timer gives a mean of returning to the reset status

when a program cannot run on a normal loop (for example, be-

cause of a software run-away). The watchdog timer consists of an

8-bit watchdog timer L and an 8-bit watchdog timer H.

Standard Operation of Watchdog Timer

When any data is not written into the watchdog timer control reg-

ister (address 003916) after resetting, the watchdog timer is in the

stop state. The watchdog timer starts to count down by writing an

optional value into the watchdog timer control register (address

003916) and an internal reset occurs at an underflow of the watch-

dog timer H.

Accordingly, programming is usually performed so that writing to

the watchdog timer control register (address 003916) may be

started before an underflow. When the watchdog timer control reg-

ister (address 003916) is read, the values of the high-order 6 bits

of the watchdog timer H, STP instruction disable bit (bit 6), and

watchdog timer H count source selection bit (bit 7) are read.

Initial Value of Watchdog Timer

At reset or writing to the watchdog timer control register (address

003916), each watchdog timer H and L is set to “FF16.”

qWatchdog timer H count source selection bit operation

Bit 7 of the watchdog timer control register (address 003916) per-

mits selecting a watchdog timer H count source. When this bit is

set to “0”, the count source becomes the underflow signal of

watchdog timer L. The detection time is set to 131.072 ms at sys-

tem clock 8 MHz frequency.

When this bit is set to “1”, the count source becomes the system

clock divided by 16. The detection time in this case is set to 512

µs at system clock 8 MHz frequency. This bit is cleared to “0” after

resetting.

qOperation of STP instruction disable bit

Bit 6 of the watchdog timer control register (address 003916) per-

mits disabling the STP instruction when the watchdog timer is in

operation.

When this bit is “0”, the STP instruction is enabled.

When this bit is “1”, the STP instruction is disabled.

Once the STP instruction is executed, an internal reset occurs.

When this bit is set to “1”, it cannot be rewritten to “0” by program.

This bit is cleared to “0” after resetting.

System clock

“0”

“1”

1/16

RESET

“FF16” is set when

watchdog timer

control register is

written to.

Watchdog timer L (8)

Watchdog timer H count

source selection bit

Watchdog timer H (8)

Data bus

“FF16” is set when

watchdog timer

control register is

written to.

STP instruction disable bit

STP instruction

Reset circuit

Internal reset

STP instruction disable bit

0: STP instruction enabled

1: STP instruction disabled

Watchdog timer H count source selection bit

0: Watchdog timer L underflow

1: System clock/16

Watchdog timer H (for read-out of high-order 6 bit)

Watchdog timer control register

(WDTCON : address 003916)

M38K02FDFP Scheda tecnica(PDF) 92 Page - Renesas Technology Corp

M38K02FDFP Scheda tecnica(HTML) 92 Page - Renesas Technology Corp

Html Pages

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65 66 67 68 69 70 71 72 73 74 75 76 77 78 79 80 81 82 83 84 85 86 87 88 89 90 91 92 93 94 95 96 97 98 99 100 ...More

Scheda tecnica Scarica

Link URL