450 datasheet(9/100 Pages) INTEL

9 / 100 page

Datasheet

Introduction

The Intel® Celeron® processor 400 series is a desktop processor that combines the

performance of the previous generation of Desktop products with the power efficiencies

of a low-power microarchitecture to enable smaller, quieter systems. Intel Celeron

Processor 400 is a 64-bit processor that maintain compatibility with IA-32 software.

The Intel Celeron processor 400 series uses a Flip-Chip Land Grid Array (FC-LGA6)

package technology, and plugs into a 775-land surface mount, Land Grid Array (LGA)

socket, referred to as the LGA775 socket.

Note:

In this document the Intel Celeron processor 400 series will be referred to as "the

processor."

Note:

In this document the Intel Celeron processor 400 series refers to the Intel Celeron

processors 420, 430, 440, and 450.

Based on 65 nm process technology, the Intel Celeron processor 400 series is a single-

core processor that features an 800 MHz front side bus (FSB), 1 MB or 512 KB L2

cache, and a thermal design power (TDP) of 35 W. The processor also supports the

Execute Disable Bit and Intel® 64 architecture.

The processor front side bus (FSB) uses a split-transaction, deferred reply protocol like

the Intel® Pentium® 4 processor. The FSB uses Source-Synchronous Transfer (SST) of

address and data to improve performance by transferring data four times per bus clock

(4X data transfer rate, as in AGP 4X). Along with the 4X data bus, the address bus can

deliver addresses two times per bus clock and is referred to as a "double-clocked" or 2X

address bus. Working together, the 4X data bus and 2X address bus provide a data bus

bandwidth of up to 6.4 GB/s.

Intel will enable support components for the processor including heatsink, heatsink

retention mechanism, and socket. Supported platforms may need to be refreshed to

ensure the correct voltage regulation (VRD11) and that PECI support is enabled.

Manufacturability is a high priority; hence, mechanical assembly may be completed

from the top of the baseboard and should not require any special tooling.

The processor includes an address bus power-down capability which removes power

from the address and data signals when the FSB is not in use. This feature is always

enabled on the processor.

1.1

Terminology

A ‘#’ symbol after a signal name refers to an active low signal, indicating a signal is in

the active state when driven to a low level. For example, when RESET# is low, a reset

has been requested. Conversely, when NMI is high, a nonmaskable interrupt has

occurred. In the case of signals where the name does not imply an active state but

describes part of a binary sequence (such as address or data), the ‘#’ symbol implies

that the signal is inverted. For example, D[3:0] = ‘HLHL’ refers to a hex ‘A’, and

D[3:0]# = ‘LHLH’ also refers to a hex ‘A’ (H= High logic level, L= Low logic level).

Front Side Bus” refers to the interface between the processor and system core logic

(a.k.a. the chipset components). The FSB is a multiprocessing interface to processors,

memory, and I/O.

450 Scheda tecnica(PDF) 9 Page - Intel Corporation

450 Scheda tecnica(HTML) 9 Page - Intel Corporation

Html Pages

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65 66 67 68 69 70 71 72 73 74 75 76 77 78 79 80 81 82 83 84 85 86 87 88 89 90 91 92 93 94 95 96 97 98 99 100

Scheda tecnica Scarica

Link URL