MPC8314VRADDA datasheet(43/101 Pages) FREESCALE

43 / 101 page

MPC8314E PowerQUICC II Pro Processor Hardware Specifications, Rev. 2

Freescale Semiconductor

JTAG

12.2

JTAG AC Timing Specifications

This section describes the AC electrical specifications for the IEEE 1149.1 (JTAG) interface. This table

provides the JTAG AC timing specifications as defined in Figure 28 through Figure 31.

Table 46. JTAG AC Timing Specifications (Independent of SYS_CLK_IN) 1

At recommended operating conditions (see Table 2)

Parameter

Symbol 2

Min

Max

Unit

Note

JTAG external clock frequency of operation

fJTG

033.3

MHz

—

JTAG external clock cycle time

t JTG

—

JTAG external clock pulse width measured at 1.4 V

tJTKHKL

—

JTAG external clock rise and fall times

tJTGR, tJTGF

—

TRST assert time

tTRST

—

Input setup times:

Boundary-scan data

TMS, TDI

tJTDVKH

tJTIVKH

—

Input hold times:

Boundary-scan data

TMS, TDI

tJTDXKH

tJTIXKH

—

Valid times:

Boundary-scan data

TDO

tJTKLDV

tJTKLOV

Output hold times:

Boundary-scan data

TDO

tJTKLDX

tJTKLOX

—

JTAG external clock to output high impedance:

Boundary-scan data

TDO

tJTKLDZ

tJTKLOZ

5, 6

Note:

1. All outputs are measured from the midpoint voltage of the falling/rising edge of tTCLK to the midpoint of the signal in question.

The output timings are measured at the pins. All output timings assume a purely resistive 50-

load (see Table 27).

Time-of-flight delays must be added for trace lengths, vias, and connectors in the system.

2. The symbols used for timing specifications herein follow the pattern of t(first two letters of functional block)(signal)(state) (reference)(state)

for inputs and t(first two letters of functional block)(reference)(state)(signal)(state) for outputs. For example, tJTDVKH symbolizes JTAG device

timing (JT) with respect to the time data input signals (D) reaching the valid state (V) relative to the tJTG clock reference (K)

going to the high (H) state or setup time. Also, tJTDXKH symbolizes JTAG timing (JT) with respect to the time data input signals

(D) went invalid (X) relative to the tJTG clock reference (K) going to the high (H) state. Note that, in general, the clock reference

symbol representation is based on three letters representing the clock of a particular functional. For rise and fall times, the

latter convention is used with the appropriate letter: R (rise) or F (fall).

3. TRST is an asynchronous level sensitive signal. The setup time is for test purposes only.

4. Non-JTAG signal input timing with respect to tTCLK.

5. Non-JTAG signal output timing with respect to tTCLK.

6. Guaranteed by design and characterization.

MPC8314VRADDA Scheda tecnica(PDF) 43 Page - Freescale Semiconductor, Inc

MPC8314VRADDA Scheda tecnica(HTML) 43 Page - Freescale Semiconductor, Inc

Html Pages

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65 66 67 68 69 70 71 72 73 74 75 76 77 78 79 80 81 82 83 84 85 86 87 88 89 90 91 92 93 94 95 96 97 98 99 100 ...More

Scheda tecnica Scarica

Link URL