WM9711 datasheet(44/66 Pages) WOLFSON

44 / 66 page

WM9711L

Production Data

PD Rev 4.1 April 2004

Table 32 Extended Power Down Register (Additional to AC’97 Rev 2.2)

Note:

*When disabling a PGA, always ensure that it is muted first.

ADDITIONAL POWER MANAGEMENT:

•

AUXDAC: see “Auxiliary DAC” section. AUXDAC is OFF by default.

SLEEP MODE

Whenever the PR4 bit (reg. 26h) is set, the AC-Link interface is disabled, and the WM9711L is in

sleep mode. There is in fact a very large number of different sleep modes, depending on the other

control bits. For example, the low-power standby mode described below is a sleep mode. It is

desirable to use sleep modes whenever possible, as this will save power. The following functions do

not require a clock and can therefore operate in sleep mode:

•

Analogue-to-analogue audio (DACs and ADCs unused), e.g. phone call mode

•

GPIO and interrupts

•

Battery alarm / analogue comparators

The WM9711L can awake from sleep mode as a result of

•

A warm reset on the AC-Link (according to the AC’97 specification)

•

A signal on a GPIO pin (if the pin is configured as an input, with wake-up enabled – see

“GPIO and Interrupt Control” section)

•

A virtual GPIO event such as battery alarm, thermal sensor, etc. (see “GPIO and

Interrupt Control” section)

ADDRESS

BIT

LABEL

DEFAULT

DESCRIPTION

PD15

0 (ON)

Disables Crystal Oscillator

PD14

0 (ON)

Disables left audio DAC

PD13

0 (ON)

Disables right audio DAC

PD12

0 (ON)

Disables left audio ADC

PD11

0 (ON)

Disables right audio ADC

PD10

0 (ON)

Disables MICBIAS

PD9

0 (ON)

Disables left headphone mixer

PD8

0 (ON)

Disables right headphone mixer

PD7

0 (ON)

Disables speaker mixer

PD6

0 (ON)

Disables MONO_OUT buffer (pin 33) and phone

mixer

PD5

0 (ON)

Disables OUT3 buffer (pin 37)

PD4

0 (ON)

Disables headphone buffers (HPOUTL/R)

PD3

0 (ON)

Disables speaker outputs (LOUT2, ROUT2)

PD2

0 (ON)

Disables Line Input PGA (left and right) *

PD1

0 (ON)

Disables Phone Input PGA *

24h

Additional

power down

control

PD0

0 (ON)

Disables Mic Input PGA (left and right) *

Note: When analogue inputs or outputs are disabled, they are internally connected to VREF

through a large resistor (VREF=AVDD/2 except in OFF mode, when VREF itself is disabled). This

maintains the potential at that node and helps to eliminate pops when the pins are re-enabled.

WM9711 Scheda tecnica(PDF) 44 Page - Wolfson Microelectronics plc

WM9711 Scheda tecnica(HTML) 44 Page - Wolfson Microelectronics plc

Html Pages

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65 66

Scheda tecnica Scarica

Link URL