AD5669RBCBZ-1-R5 datasheet(28/30 Pages) AD

28 / 30 page

AD5629R/AD5669R

Data Sheet

Rev. F | Page 28 of 30

LDAC FUNCTION

The outputs of all DACs can be updated simultaneously using

the hardware LDAC pin.

Synchronous LDAC

The DAC registers are updated after new data is read in. LDAC

can be permanently low or pulsed as in Figure 2.

Asynchronous LDAC

The outputs are not updated at the same time that the input

registers are written to. When LDAC goes low, the DAC

registers are updated with the contents of the input register.

Alternatively, the outputs of all DACs can be updated simulta-

neously using the software LDAC function by writing to Input

reserved for this software LDAC function.

An LDAC register gives the user extra flexibility and control

over the hardware LDAC pin. Setting the LDAC bit register

to 0 for a DAC channel means that this channel’s update is

controlled by the LDAC pin. If this bit is set to 1, this channel

updates synchronously; that is, the DAC register is updated

after new data is read, regardless of the state of the LDAC pin.

It effectively sees the LDAC pin as being tied low. See Table 16

for the LDAC register mode of operation.

This flexibility is useful in applications where the user wants

to simultaneously update select channels while the rest of the

channels are synchronously updating. Writing to the DAC

using command 0110 loads the 8-bit LDAC register (DB7 to

DB0). The default for each channel is 0, that is, the LDAC pin

works normally. Setting the bits to 1 means the DAC channel

is updated regardless of the state of the LDAC pin. See Table 17

for the contents of the input shift register during the load LDAC

POWER SUPPLY BYPASSING AND GROUNDING

When accuracy is important in a circuit, it is helpful to carefully

consider the power supply and ground return layout on the board.

The printed circuit board containing the AD5629R/AD5669R

should have separate analog and digital sections. If the AD5629R/

AD5669R are in a system where other devices require an

AGND-to-DGND connection, the connection should be made

at one point only. This ground point should be as close as

possible to the AD5629R/AD5669R.

The power supply to the AD5629R/AD5669R should be

bypassed with 10 µF and 0.1 µF capacitors. The capacitors

should be as physically close as possible to the device, with the

0.1 µF capacitor ideally right up against the device. The 10 µF

capacitors are the tantalum bead type. It is important that the

0.1 µF capacitor have low effective series resistance (ESR) and

low effective series inductance (ESI), such as is typical of

common ceramic types of capacitors. This 0.1 µF capacitor

provides a low impedance path to ground for high frequencies

caused by transient currents due to internal logic switching.

The power supply line should have as large a trace as possible to

provide a low impedance path and reduce glitch effects on the

supply line. Clocks and other fast switching digital signals should

be shielded from other parts of the board by digital ground. Avoid

crossover of digital and analog signals if possible. When traces

cross on opposite sides of the board, ensure that they run at right

angles to each other to reduce feedthrough effects through the

board. The best board layout technique is the microstrip technique,

where the component side of the board is dedicated to the ground

plane only and the signal traces are placed on the solder side.

However, this is not always possible with a 2-layer board.

Table 16. LDAC Register

Load DAC Register

LDAC Bits (DB7 to DB0)

LDAC Pin

LDAC Operation

1/0

Determined by LDAC pin.

X—don’t care

DAC channels update, overriding the LDAC pin. DAC channels see LDAC as 0.

Table 17. 32-Bit Input Shift Register Contents for LDAC Register Function

MSB

LSB

DB23

DB22

DB21

DB20

DB19

DB18

DB17

DB16

DB15

to DB8

DB7

DB6

DB5

DB4

DB3

DB2

DB1

DB0

DAC H

DAC G

DAC F

DAC E

DAC D

DAC C

DAC B

DAC A

Command bits (C3 to C0)

Address bits (A3 to A0)—

don’t cares

Don’t

cares

Setting LDAC bit to 1 overrides LDAC pin

AD5669RBCBZ-1-R5 Scheda tecnica(PDF) 28 Page - Analog Devices

AD5669RBCBZ-1-R5 Scheda tecnica(HTML) 28 Page - Analog Devices

Html Pages

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30

Scheda tecnica Scarica

Link URL