MAX96708 datasheet(19/68 Pages) MAXIM

19 / 68 page

NAME

FUNCTION

REF SUPPLY

TYPE

DOUT7/

ADD1

Parallel-Data Output/Address Input with Internal Pulldown to EP.

ADD1 is latched at power-up, or when resuming from power-down

mode (PWDNB = low), and switches to parallel-data output after

power-up. Connect ADD1 to IOVDD with a 30kΩ resistor to set

high, or leave open to set low.

IOVDD

Digital

DOUT6/

ADD0

Parallel-Data Output/Address Input with Internal Pulldown to EP.

ADD0 is latched at power-up, or when resuming from power-down

mode (PWDNB = low), and switches to parallel-data output after

power-up. Connect ADD0 to IOVDD with a 30kΩ resistor to set

high, or leave open to set low.

IOVDD

Digital

DOUT5/HIM

Parallel-Data Output/High-Immunity Mode Input with Internal

Pulldown to EP. HIM input latched at power-up, or when resuming

from power-down mode (PWDNB = low), and switches to parallel-

data output after power-up. Connect HIM to IOVDD with a 30kΩ

resistor to set high, or leave open to set low. HIGHIMM in the

serializer must be set to the same value.

IOVDD

Digital

High-Speed Digital / Single Function

PCLKOUT

Parallel-Clock Output. Provides timing signal to latch parallel-data

outputs to the input of another device.

IOVDD

Digital

DOUT4

Parallel-Data Output

IOVDD

Digital

DOUT3

Parallel-Data Output

IOVDD

Digital

DOUT2

Parallel-Data Output

IOVDD

Digital

DOUT1

Parallel-Data Output

IOVDD

Digital

DOUT0

Parallel-Data Output

IOVDD

Digital

LINE FAULT

LMN1

Line-Fault Monitor Input 1 (see Figure 4)

Analog

LMN0

Line-Fault Monitor Input 0 (see Figure 4)

Analog

LFLTB

Line-Fault Output. LFLTB is active low, and has a 60kΩ internal pullup

to IOVDD. LFLTB low indicates a line-fault condition at LMN0, or

LMN1. LFLTB is output high when PWDNB is low.

IOVDD

Digital

OTHER PINS

GPI

General-Purpose Input with Internal Pulldown to EP. Serializer

GPO (or INT) output follows the state of the GPI.

IOVDD

Digital

IN1+

Noninverting CML Serial-Data Input 1. Coax input when CXTP

is high.

IN1-

Inverting CML Serial-Data Input 1

IN0+

Noninverting CML Serial-Data Input 0. Coax input when CXTP

is high.

IN0-

Inverting CML Serial-Data Input 0

RX/SDA

Receive/Serial Data. Input/output with internal 30kΩ pullup to

IOVDD. In UART mode, RX/SDA is the Rx input of the

serializer's UART. In I2C mode, RX/SDA is the SDA input/output

of the serializer's I2C master/slave. RX/SDA has an open-drain

driver and requires a pullup resistor.

IOVDD

Digital

Pin Description (continued)

www.maximintegrated.com

Maxim Integrated │ 19

MAX96708

14-Bit GMSL Deserializer

with Coax or STP Cable Input

MAX96708 Scheda tecnica(PDF) 19 Page - Maxim Integrated Products

MAX96708 Scheda tecnica(HTML) 19 Page - Maxim Integrated Products

Html Pages

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65 66 67 68

Scheda tecnica Scarica

Link URL