OPA387DBVT datasheet(17/37 Pages) TI

17 / 37 page

8.2.1.1 Design Requirements

This solution has the following requirements:

• Supply voltage: 3.3 V

• Input: –1 A to +1 A

• Output: 1.65 V ±1.54 V (110 mV to 3.19 V)

8.2.1.2 Detailed Design Procedure

The load current, ILOAD, flows through the shunt resistor, RSHUNT, to develop the shunt voltage, VSHUNT. The

shunt voltage is then amplified by the difference amplifier consisting of U1A and R1 through R4. The gain of the

difference amplifier is set by the ratio of R4 to R3. To minimize errors, set R2 = R4 and R1 = R3. The reference

voltage, VREF, is supplied by buffering a resistor divider using U1B. The transfer function is given by Equation 1.

= V

Gain

+ V

OUT

SHUNT

Diff_Amp

REF

(1)

where

• V

= I

SHUNT

LOAD

SHUNT

•

Gain

Diff_Amp

•

= V

REF

There are two types of errors in this design: gain and offset. Gain errors are introduced by the tolerance of the

shunt resistor and the ratios of R4 to R3 and, similarly, R2 to R1. Offset errors are introduced by the voltage

divider (R5 and R6) and how closely the ratio of R4 / R3 matches R2 / R1. The latter value affects the CMRR of

the difference amplifier, ultimately translating to an offset error.

The value of VSHUNT is the ground potential for the system load because VSHUNT is a low-side measurement.

Therefore, a maximum value must be placed on VSHUNT. In this design, the maximum value for VSHUNT is set

to 100 mV. Equation 2 calculates the maximum value of the shunt resistor given a maximum shunt voltage of

100 mV and maximum load current of 1 A.

SHUNT(Max)

= 100 mW

SHUNT(Max)

LOAD(Max)

100 mV

1 A

(2)

The tolerance of RSHUNT is directly proportional to cost. For this design, a shunt resistor with a tolerance of 0.5%

is selected. If greater accuracy is required, select a 0.1% resistor or better.

The load current is bidirectional; therefore, the shunt voltage range is –100 mV to +100 mV. This voltage is

divided down by R1 and R2 before reaching the operational amplifier, U1A. Make sure that the voltage present at

the noninverting node of U1A is within the common-mode range of the device. Use an operational amplifier, such

as the OPAx387, that has a common-mode range that extends below the negative supply voltage. The offset

error is minimal because the OPAx387 has a typical offset voltage of merely ±0.25 µV (±5 µV, maximum).

Given a symmetric load current of –1 A to +1 A, the voltage divider resistors, R5 and R6, must be equal. To

be consistent with the shunt resistor, a tolerance of 0.5% is selected. To minimize power consumption, 10

‑kΩ

resistors are used.

To set the gain of the difference amplifier, the common-mode range and output swing of the OPAx387 must

be considered. Equation 3 and Equation 4 depict the typical common-mode range and maximum output swing,

respectively, of the OPAx387 given a 3.3

‑V supply.

–100 mV < VCM < 3.4 V

(3)

100 mV < VOUT < 3.2 V

(4)

www.ti.com

OPA387, OPA2387, OPA4387

SBOS984F – NOVEMBER 2020 – REVISED FEBRUARY 2022

Submit Document Feedback

Product Folder Links: OPA387 OPA2387 OPA4387

OPA387DBVT Scheda tecnica(PDF) 17 Page - Texas Instruments

OPA387DBVT Scheda tecnica(HTML) 17 Page - Texas Instruments

Html Pages

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37

Scheda tecnica Scarica

Link URL