AM486DX2 datasheet(58/67 Pages) AMD

58 / 67 page

Am5X86 Microprocessor

AMD

PRELIMINARY

ABSOLUTE MAXIMUM RATINGS

Case Temperature under Bias . . . – 65°C to +110°C

Storage Temperature . . . . . . . . . . – 65°C to +150°C

Voltage on any pin

with respect to ground . . . . . . – 0.5 V to Vcc +2.6 V

Supply voltage with

respect to VSS . . . . . . . . . . . . . . – 0.5 V to +4.6 V

Stresses above those listed under Absolute Maximum Ratings

may cause permanent device failure. Functionality at or above

these limits is not implied. Exposure to Absolute Maximum

Ratings for extended periods may affect device reliability.

OPERATING RANGES

Commercial (C) Devices

TCASE . . . . . . . . . . . . . . . . . . . . . . . . . . . 0°C to 85°C

VCC . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3.3 V ±0.3 V

Operating Ranges define those limits between which the func-

tionality of the device is guaranteed.

DC CHARACTERISTICS over COMMERCIAL operating ranges

CC = 3.3 V ± 0.3 V; TCASE = 0°C to + 85°C

Preliminary Info

Symbol

Parameter

Min

Max

Notes

VIL

Input Low Voltage

– 0.3 V

+0.8 V

VIH

Input High Voltage

2.0 V

VCC + 2.4 V

VOL

Output Low Voltage

0.45 V

Note 1

VOH

Output High Voltage

2.4 V

Note 2

ICC

Power Supply Current:

133 MHz

931 mA

Typical supply current: 825 mA @ 133

MHz. Inputs at rails, outputs unloaded.

ICCSTOPGRANT

or ICCAUTOHALT

Input Current in Stop Grant or Auto Halt mode:

133 MHz

93 mA

Typical supply current for Stop Grant or

Auto Halt mode: 50 mA @ 133 MHz.

ICCSTPCLK

Input Current in Stop Clock mode

5 mA

Typical supply current in Stop Clock

mode is 600

µA.

ILI

Input Leakage Current

±15 µA

Note 3

IIH

Input Leakage Current

200 µA

Note 4

IIL

Input Leakage Current

– 400 µA

Note 5

ILO

Output Leakage Current

±15 µA

CIN

Input Capacitance

10 pF

FC = 1 MHz (Note 6)

I/O or Output Capacitance

14 pF

FC = 1 MHz (Note 6)

CCLK

CLK Capacitance

12 pF

FC = 1 MHz (Note 6)

Notes:

1. This parameter is measured at: Address, Data, BE3 –BE0 = 4.0 mA; Definition, Control = 5.0 mA

2. This parameter is measured at: Address, Data, BE3 –BE0 = –1.0 mA; Definition, Control = –0.9 mA

3. This parameter is for inputs without internal pull-ups or pull-downs and 0

≤ V

IN ≤ VCC.

4. This parameter is for inputs with internal pull-downs and VIH = 2.4 V.

5. This parameter is for inputs with internal pull-ups and VIL = 0.45 V.

6. Not 100% tested.

AM486DX2 Scheda tecnica(PDF) 58 Page - Advanced Micro Devices

AM486DX2 Scheda tecnica(HTML) 58 Page - Advanced Micro Devices

Html Pages

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65 66 67

Scheda tecnica Scarica

Link URL